EBIKE-FreeRTOS/Common/drivers/Atmel/at91lib/peripherals/usart/usart.h

113 lines
4.4 KiB
C
Raw Normal View History

2024-04-14 18:38:39 +08:00
/* ----------------------------------------------------------------------------
* ATMEL Microcontroller Software Support
* ----------------------------------------------------------------------------
* Copyright (c) 2008, Atmel Corporation
*
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* - Redistributions of source code must retain the above copyright notice,
* this list of conditions and the disclaimer below.
*
* Atmel's name may not be used to endorse or promote products derived from
* this software without specific prior written permission.
*
* DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
* OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
* ----------------------------------------------------------------------------
*/
//------------------------------------------------------------------------------
/// \dir
/// !Purpose
///
/// This module provides several definitions and methods for using an USART
/// peripheral.
///
/// !Usage
/// -# Enable the USART peripheral clock in the PMC.
/// -# Enable the required USART PIOs (see pio.h).
/// -# Configure the UART by calling USART_Configure.
/// -# Enable the transmitter and/or the receiver of the USART using
/// USART_SetTransmitterEnabled and USART_SetReceiverEnabled.
/// -# Send data through the USART using the USART_Write and
/// USART_WriteBuffer methods.
/// -# Receive data from the USART using the USART_Read and
/// USART_ReadBuffer functions; the availability of data can be polled
/// with USART_IsDataAvailable.
/// -# Disable the transmitter and/or the receiver of the USART with
/// USART_SetTransmitterEnabled and USART_SetReceiverEnabled.
//------------------------------------------------------------------------------
#ifndef USART_H
#define USART_H
//------------------------------------------------------------------------------
// Headers
//------------------------------------------------------------------------------
#include <board.h>
//------------------------------------------------------------------------------
// Definitions
//------------------------------------------------------------------------------
//------------------------------------------------------------------------------
/// \page "USART modes"
/// This page lists several common operating modes for an USART peripheral.
///
/// !Modes
/// - USART_MODE_ASYNCHRONOUS
/// Basic asynchronous mode, i.e. 8 bits no parity.
#define USART_MODE_ASYNCHRONOUS (AT91C_US_CHRL_8_BITS | AT91C_US_PAR_NONE)
//------------------------------------------------------------------------------
//------------------------------------------------------------------------------
// Exported functions
//------------------------------------------------------------------------------
extern void USART_Configure(
AT91S_USART *usart,
unsigned int mode,
unsigned int baudrate,
unsigned int masterClock);
extern void USART_SetTransmitterEnabled(AT91S_USART *usart, unsigned char enabled);
extern void USART_SetReceiverEnabled(AT91S_USART *usart, unsigned char enabled);
extern void USART_Write(
AT91S_USART *usart,
unsigned short data,
volatile unsigned int timeOut);
extern unsigned char USART_WriteBuffer(
AT91S_USART *usart,
void *buffer,
unsigned int size);
extern unsigned short USART_Read(
AT91S_USART *usart,
volatile unsigned int timeOut);
extern unsigned char USART_ReadBuffer(
AT91S_USART *usart,
void *buffer,
unsigned int size);
extern unsigned char USART_IsDataAvailable(AT91S_USART *usart);
#endif //#ifndef USART_H