260 lines
9.2 KiB
C
260 lines
9.2 KiB
C
/* ----------------------------------------------------------------------------
|
|
* ATMEL Microcontroller Software Support
|
|
* ----------------------------------------------------------------------------
|
|
* Copyright (c) 2008, Atmel Corporation
|
|
*
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are met:
|
|
*
|
|
* - Redistributions of source code must retain the above copyright notice,
|
|
* this list of conditions and the disclaimer below.
|
|
*
|
|
* Atmel's name may not be used to endorse or promote products derived from
|
|
* this software without specific prior written permission.
|
|
*
|
|
* DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
|
|
* DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
|
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
|
|
* OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
|
|
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
|
|
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
|
|
* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
* ----------------------------------------------------------------------------
|
|
*/
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Headers
|
|
//------------------------------------------------------------------------------
|
|
|
|
#include "usart.h"
|
|
#include <utility/trace.h>
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Exported functions
|
|
//------------------------------------------------------------------------------
|
|
//------------------------------------------------------------------------------
|
|
/// Configures an USART peripheral with the specified parameters.
|
|
/// \param usart Pointer to the USART peripheral to configure.
|
|
/// \param mode Desired value for the USART mode register (see the datasheet).
|
|
/// \param baudrate Baudrate at which the USART should operate (in Hz).
|
|
/// \param masterClock Frequency of the system master clock (in Hz).
|
|
//------------------------------------------------------------------------------
|
|
void USART_Configure(AT91S_USART *usart,
|
|
unsigned int mode,
|
|
unsigned int baudrate,
|
|
unsigned int masterClock)
|
|
{
|
|
// Reset and disable receiver & transmitter
|
|
usart->US_CR = AT91C_US_RSTRX | AT91C_US_RSTTX
|
|
| AT91C_US_RXDIS | AT91C_US_TXDIS;
|
|
|
|
// Configure mode
|
|
usart->US_MR = mode;
|
|
|
|
// Configure baudrate
|
|
// Asynchronous, no oversampling
|
|
if (((mode & AT91C_US_SYNC) == 0)
|
|
&& ((mode & AT91C_US_OVER) == 0)) {
|
|
|
|
usart->US_BRGR = (masterClock / baudrate) / 16;
|
|
}
|
|
// TODO other modes
|
|
}
|
|
|
|
//------------------------------------------------------------------------------
|
|
/// Enables or disables the transmitter of an USART peripheral.
|
|
/// \param usart Pointer to an USART peripheral
|
|
/// \param enabled If true, the transmitter is enabled; otherwise it is
|
|
/// disabled.
|
|
//------------------------------------------------------------------------------
|
|
void USART_SetTransmitterEnabled(AT91S_USART *usart,
|
|
unsigned char enabled)
|
|
{
|
|
if (enabled) {
|
|
|
|
usart->US_CR = AT91C_US_TXEN;
|
|
}
|
|
else {
|
|
|
|
usart->US_CR = AT91C_US_TXDIS;
|
|
}
|
|
}
|
|
|
|
//------------------------------------------------------------------------------
|
|
/// Enables or disables the receiver of an USART peripheral
|
|
/// \param usart Pointer to an USART peripheral
|
|
/// \param enabled If true, the receiver is enabled; otherwise it is disabled.
|
|
//------------------------------------------------------------------------------
|
|
void USART_SetReceiverEnabled(AT91S_USART *usart,
|
|
unsigned char enabled)
|
|
{
|
|
if (enabled) {
|
|
|
|
usart->US_CR = AT91C_US_RXEN;
|
|
}
|
|
else {
|
|
|
|
usart->US_CR = AT91C_US_RXDIS;
|
|
}
|
|
}
|
|
|
|
//------------------------------------------------------------------------------
|
|
/// Sends one packet of data through the specified USART peripheral. This
|
|
/// function operates synchronously, so it only returns when the data has been
|
|
/// actually sent.
|
|
/// \param usart Pointer to an USART peripheral.
|
|
/// \param data Data to send including 9nth bit and sync field if necessary (in
|
|
/// the same format as the US_THR register in the datasheet).
|
|
/// \param timeOut Time out value (0 = no timeout).
|
|
//------------------------------------------------------------------------------
|
|
void USART_Write(
|
|
AT91S_USART *usart,
|
|
unsigned short data,
|
|
volatile unsigned int timeOut)
|
|
{
|
|
if (timeOut == 0) {
|
|
|
|
while ((usart->US_CSR & AT91C_US_TXEMPTY) == 0);
|
|
}
|
|
else {
|
|
|
|
while ((usart->US_CSR & AT91C_US_TXEMPTY) == 0) {
|
|
|
|
if (timeOut == 0) {
|
|
|
|
trace_LOG(trace_ERROR, "-E- USART_Write: Timed out.\n\r");
|
|
return;
|
|
}
|
|
timeOut--;
|
|
}
|
|
}
|
|
|
|
usart->US_THR = data;
|
|
}
|
|
|
|
//------------------------------------------------------------------------------
|
|
/// Sends the contents of a data buffer through the specified USART peripheral.
|
|
/// This function returns immediately (1 if the buffer has been queued, 0
|
|
/// otherwise); poll the ENDTX and TXBUFE bits of the USART status register
|
|
/// to check for the transfer completion.
|
|
/// \param usart Pointer to an USART peripheral.
|
|
/// \param buffer Pointer to the data buffer to send.
|
|
/// \param size Size of the data buffer (in bytes).
|
|
//------------------------------------------------------------------------------
|
|
unsigned char USART_WriteBuffer(
|
|
AT91S_USART *usart,
|
|
void *buffer,
|
|
unsigned int size)
|
|
{
|
|
// Check if the first PDC bank is free
|
|
if ((usart->US_TCR == 0) && (usart->US_TNCR == 0)) {
|
|
|
|
usart->US_TPR = (unsigned int) buffer;
|
|
usart->US_TCR = size;
|
|
usart->US_PTCR = AT91C_PDC_TXTEN;
|
|
|
|
return 1;
|
|
}
|
|
// Check if the second PDC bank is free
|
|
else if (usart->US_TNCR == 0) {
|
|
|
|
usart->US_TNPR = (unsigned int) buffer;
|
|
usart->US_TNCR = size;
|
|
|
|
return 1;
|
|
}
|
|
else {
|
|
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
//------------------------------------------------------------------------------
|
|
/// Reads and return a packet of data on the specified USART peripheral. This
|
|
/// function operates asynchronously, so it waits until some data has been
|
|
/// received.
|
|
/// \param usart Pointer to an USART peripheral.
|
|
/// \param timeOut Time out value (0 -> no timeout).
|
|
//------------------------------------------------------------------------------
|
|
unsigned short USART_Read(
|
|
AT91S_USART *usart,
|
|
volatile unsigned int timeOut)
|
|
{
|
|
if (timeOut == 0) {
|
|
|
|
while ((usart->US_CSR & AT91C_US_RXRDY) == 0);
|
|
}
|
|
else {
|
|
|
|
while ((usart->US_CSR & AT91C_US_RXRDY) == 0) {
|
|
|
|
if (timeOut == 0) {
|
|
|
|
trace_LOG(trace_ERROR, "-E- USART_Read: Timed out.\n\r");
|
|
return 0;
|
|
}
|
|
timeOut--;
|
|
}
|
|
}
|
|
|
|
return usart->US_RHR;
|
|
}
|
|
|
|
//------------------------------------------------------------------------------
|
|
/// Reads data from an USART peripheral, filling the provided buffer until it
|
|
/// becomes full. This function returns immediately with 1 if the buffer has
|
|
/// been queued for transmission; otherwise 0.
|
|
/// \param usart Pointer to an USART peripheral.
|
|
/// \param buffer Pointer to the buffer where the received data will be stored.
|
|
/// \param size Size of the data buffer (in bytes).
|
|
//------------------------------------------------------------------------------
|
|
unsigned char USART_ReadBuffer(AT91S_USART *usart,
|
|
void *buffer,
|
|
unsigned int size)
|
|
{
|
|
// Check if the first PDC bank is free
|
|
if ((usart->US_RCR == 0) && (usart->US_RNCR == 0)) {
|
|
|
|
usart->US_RPR = (unsigned int) buffer;
|
|
usart->US_RCR = size;
|
|
usart->US_PTCR = AT91C_PDC_RXTEN;
|
|
|
|
return 1;
|
|
}
|
|
// Check if the second PDC bank is free
|
|
else if (usart->US_RNCR == 0) {
|
|
|
|
usart->US_RNPR = (unsigned int) buffer;
|
|
usart->US_RNCR = size;
|
|
|
|
return 1;
|
|
}
|
|
else {
|
|
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
//------------------------------------------------------------------------------
|
|
/// Returns 1 if some data has been received and can be read from an USART;
|
|
/// otherwise returns 0.
|
|
/// \param usart Pointer to an AT91S_USART instance.
|
|
//------------------------------------------------------------------------------
|
|
unsigned char USART_IsDataAvailable(AT91S_USART *usart)
|
|
{
|
|
if ((usart->US_CSR & AT91C_US_RXRDY) != 0) {
|
|
|
|
return 1;
|
|
}
|
|
else {
|
|
|
|
return 0;
|
|
}
|
|
}
|
|
|