856 lines
18 KiB
Plaintext
856 lines
18 KiB
Plaintext
|
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||
|
|
/*
|
||
|
|
* Copyright (c) 2020 Rockchip Electronics Co., Ltd.
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
/dts-v1/;
|
||
|
|
|
||
|
|
#include <dt-bindings/gpio/gpio.h>
|
||
|
|
#include <dt-bindings/pwm/pwm.h>
|
||
|
|
#include <dt-bindings/pinctrl/rockchip.h>
|
||
|
|
#include <dt-bindings/soc/rockchip,vop2.h>
|
||
|
|
#include "rk3566.dtsi"
|
||
|
|
|
||
|
|
/ {
|
||
|
|
model = "Rockchip RK3566 OPi 3B";
|
||
|
|
compatible = "rockchip,rk3566-orangepi-3b", "rockchip,rk3566";
|
||
|
|
|
||
|
|
aliases {
|
||
|
|
ethernet0 = &gmac1;
|
||
|
|
mmc0 = &sdhci;
|
||
|
|
mmc1 = &sdmmc0;
|
||
|
|
};
|
||
|
|
|
||
|
|
chosen: chosen {
|
||
|
|
stdout-path = "serial2:1500000n8";
|
||
|
|
};
|
||
|
|
|
||
|
|
fan: pwm-fan {
|
||
|
|
compatible = "pwm-fan";
|
||
|
|
#cooling-cells = <2>;
|
||
|
|
pwms = <&pwm7 0 50000 0>;
|
||
|
|
cooling-levels = <0 50 100 150 200 255>;
|
||
|
|
rockchip,temp-trips = <
|
||
|
|
50000 1
|
||
|
|
55000 2
|
||
|
|
60000 3
|
||
|
|
65000 4
|
||
|
|
70000 5
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
hdmi-con {
|
||
|
|
compatible = "hdmi-connector";
|
||
|
|
type = "a";
|
||
|
|
|
||
|
|
port {
|
||
|
|
hdmi_con_in: endpoint {
|
||
|
|
remote-endpoint = <&hdmi_out_con>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
leds: leds {
|
||
|
|
compatible = "gpio-leds";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 =<&leds_gpio>;
|
||
|
|
|
||
|
|
led@1 {
|
||
|
|
gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
|
||
|
|
label = "status_led";
|
||
|
|
linux,default-trigger = "heartbeat";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
rk809-sound {
|
||
|
|
compatible = "simple-audio-card";
|
||
|
|
simple-audio-card,format = "i2s";
|
||
|
|
simple-audio-card,name = "Analog RK809";
|
||
|
|
simple-audio-card,mclk-fs = <256>;
|
||
|
|
|
||
|
|
simple-audio-card,cpu {
|
||
|
|
sound-dai = <&i2s1_8ch>;
|
||
|
|
};
|
||
|
|
|
||
|
|
simple-audio-card,codec {
|
||
|
|
sound-dai = <&rk809>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
sdio_pwrseq: sdio-pwrseq {
|
||
|
|
compatible = "mmc-pwrseq-simple";
|
||
|
|
clocks = <&rk809 1>;
|
||
|
|
clock-names = "ext_clock";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&wifi_enable_h>;
|
||
|
|
|
||
|
|
/*
|
||
|
|
* On the module itself this is one of these (depending
|
||
|
|
* on the actual card populated):
|
||
|
|
* - SDIO_RESET_L_WL_REG_ON
|
||
|
|
* - PDN (power down when low)
|
||
|
|
*/
|
||
|
|
post-power-on-delay-ms = <200>;
|
||
|
|
reset-gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
|
||
|
|
unisoc_uwe_bsp: uwe-bsp {
|
||
|
|
compatible = "unisoc,uwe_bsp";
|
||
|
|
wl-reg-on = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
|
||
|
|
bt-reg-on = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||
|
|
wl-wake-host-gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
|
||
|
|
bt-wake-host-gpio = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
|
||
|
|
sdio-ext-int-gpio = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
|
||
|
|
unisoc,btwf-file-name = "/lib/firmware/wcnmodem.bin";
|
||
|
|
data-irq;
|
||
|
|
blksz-512;
|
||
|
|
keep-power-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* labeled +12v in schematic */
|
||
|
|
vcc12v_dcin: vcc12v-dcin-regulator {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "vcc12v_dcin";
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <12000000>;
|
||
|
|
regulator-max-microvolt = <12000000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* labeled +5v in schematic */
|
||
|
|
vcc_5v: vcc-5v-regulator {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "vcc_5v";
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <5000000>;
|
||
|
|
regulator-max-microvolt = <5000000>;
|
||
|
|
vin-supply = <&vcc12v_dcin>;
|
||
|
|
};
|
||
|
|
|
||
|
|
vbus: vbus {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "vbus";
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <5000000>;
|
||
|
|
regulator-max-microvolt = <5000000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* labeled +3.3v For PCIe only in schematic */
|
||
|
|
vcc3v3_pcie: vcc3v3-pcie-regulator {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "vcc3v3_pcie";
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pcie_drv>;
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
vin-supply = <&vcc12v_dcin>;
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc3v3_sys: vcc3v3-sys {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "vcc3v3_sys";
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
vin-supply = <&vbus>;
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc5v0_sys: vcc5v0-sys {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "vcc5v0_sys";
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <5000000>;
|
||
|
|
regulator-max-microvolt = <5000000>;
|
||
|
|
vin-supply = <&vbus>;
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc5v0_usb: vcc5v0-usb {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "vcc5v0_usb";
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <5000000>;
|
||
|
|
regulator-max-microvolt = <5000000>;
|
||
|
|
vin-supply = <&vbus>;
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc_sd: vcc-sd {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-name = "vcc_sd";
|
||
|
|
vin-supply = <&vcc3v3_sys>;
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc5v0_host: vcc5v0-host-regulator {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&vcc5v0_host_en>;
|
||
|
|
regulator-name = "vcc5v0_host";
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc5v0_otg: vcc5v0-otg-regulator {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&vcc5v0_otg_en>;
|
||
|
|
regulator-name = "vcc5v0_otg";
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&combphy1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&combphy2 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&cpu0 {
|
||
|
|
cpu-supply = <&vdd_cpu>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&cpu1 {
|
||
|
|
cpu-supply = <&vdd_cpu>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&cpu2 {
|
||
|
|
cpu-supply = <&vdd_cpu>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&cpu3 {
|
||
|
|
cpu-supply = <&vdd_cpu>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&gmac1 {
|
||
|
|
assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
|
||
|
|
assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
|
||
|
|
assigned-clock-rates = <0>, <125000000>;
|
||
|
|
clock_in_out = "input";
|
||
|
|
phy-mode = "rgmii";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&gmac1m0_miim
|
||
|
|
&gmac1m0_tx_bus2
|
||
|
|
&gmac1m0_rx_bus2
|
||
|
|
&gmac1m0_rgmii_clk
|
||
|
|
&gmac1m0_clkinout
|
||
|
|
&gmac1m0_rgmii_bus>;
|
||
|
|
|
||
|
|
snps,reset-gpio = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
|
||
|
|
snps,reset-active-low;
|
||
|
|
/* Reset time is 20ms, 100ms for rtl8211f */
|
||
|
|
//snps,reset-delays-us = <0 20000 100000>;
|
||
|
|
snps,reset-delays-us = <0 50000 200000>;
|
||
|
|
tx_delay = <0x30>;
|
||
|
|
rx_delay = <0x10>;
|
||
|
|
phy-handle = <&rgmii_phy0>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&gpu {
|
||
|
|
mali-supply = <&vdd_gpu>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&hdmi {
|
||
|
|
avdd-0v9-supply = <&vdda0v9_image>;
|
||
|
|
avdd-1v8-supply = <&vcca1v8_image>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&hdmi_in {
|
||
|
|
hdmi_in_vp0: endpoint {
|
||
|
|
remote-endpoint = <&vp0_out_hdmi>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&hdmi_out {
|
||
|
|
hdmi_out_con: endpoint {
|
||
|
|
remote-endpoint = <&hdmi_con_in>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&hdmi_sound {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&i2c0 {
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
vdd_cpu: syr837@40 {
|
||
|
|
compatible = "silergy,syr827";
|
||
|
|
reg = <0x40>;
|
||
|
|
vin-supply = <&vcc5v0_sys>;
|
||
|
|
regulator-compatible = "fan53555-reg";
|
||
|
|
regulator-name = "vdd_cpu";
|
||
|
|
regulator-min-microvolt = <712500>;
|
||
|
|
regulator-max-microvolt = <1390000>;
|
||
|
|
regulator-init-microvolt = <900000>;
|
||
|
|
regulator-initial-mode = <1>;
|
||
|
|
regulator-ramp-delay = <2300>;
|
||
|
|
fcs,suspend-voltage-selector = <1>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
rk809: pmic@20 {
|
||
|
|
compatible = "rockchip,rk809";
|
||
|
|
reg = <0x20>;
|
||
|
|
interrupt-parent = <&gpio0>;
|
||
|
|
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
||
|
|
|
||
|
|
assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
|
||
|
|
assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
|
||
|
|
#clock-cells = <1>;
|
||
|
|
clock-names = "mclk";
|
||
|
|
clocks = <&cru I2S1_MCLKOUT_TX>;
|
||
|
|
pinctrl-names = "default", "pmic-sleep",
|
||
|
|
"pmic-power-off", "pmic-reset";
|
||
|
|
pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
|
||
|
|
pinctrl-1 = <&soc_slppin_slp>, <&rk817_slppin_slp>;
|
||
|
|
pinctrl-2 = <&soc_slppin_gpio>, <&rk817_slppin_pwrdn>;
|
||
|
|
pinctrl-3 = <&soc_slppin_gpio>, <&rk817_slppin_rst>;
|
||
|
|
#sound-dai-cells = <0>;
|
||
|
|
|
||
|
|
rockchip,system-power-controller;
|
||
|
|
wakeup-source;
|
||
|
|
|
||
|
|
vcc1-supply = <&vcc3v3_sys>;
|
||
|
|
vcc2-supply = <&vcc3v3_sys>;
|
||
|
|
vcc3-supply = <&vcc3v3_sys>;
|
||
|
|
vcc4-supply = <&vcc3v3_sys>;
|
||
|
|
vcc5-supply = <&vcc3v3_sys>;
|
||
|
|
vcc6-supply = <&vcc3v3_sys>;
|
||
|
|
vcc7-supply = <&vcc3v3_sys>;
|
||
|
|
vcc8-supply = <&vcc3v3_sys>;
|
||
|
|
vcc9-supply = <&vcc3v3_sys>;
|
||
|
|
|
||
|
|
pinctrl_rk8xx: pinctrl_rk8xx {
|
||
|
|
gpio-controller;
|
||
|
|
#gpio-cells = <2>;
|
||
|
|
|
||
|
|
rk817_slppin_null: rk817_slppin_null {
|
||
|
|
pins = "gpio_slp";
|
||
|
|
function = "pin_fun0";
|
||
|
|
};
|
||
|
|
|
||
|
|
rk817_slppin_slp: rk817_slppin_slp {
|
||
|
|
pins = "gpio_slp";
|
||
|
|
function = "pin_fun1";
|
||
|
|
};
|
||
|
|
|
||
|
|
rk817_slppin_pwrdn: rk817_slppin_pwrdn {
|
||
|
|
pins = "gpio_slp";
|
||
|
|
function = "pin_fun2";
|
||
|
|
};
|
||
|
|
|
||
|
|
rk817_slppin_rst: rk817_slppin_rst {
|
||
|
|
pins = "gpio_slp";
|
||
|
|
function = "pin_fun3";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
regulators {
|
||
|
|
vdd_logic: DCDC_REG1 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <500000>;
|
||
|
|
regulator-max-microvolt = <1350000>;
|
||
|
|
regulator-init-microvolt = <900000>;
|
||
|
|
regulator-ramp-delay = <6001>;
|
||
|
|
regulator-initial-mode = <0x2>;
|
||
|
|
regulator-name = "vdd_logic";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vdd_gpu: DCDC_REG2 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <500000>;
|
||
|
|
regulator-max-microvolt = <1350000>;
|
||
|
|
regulator-init-microvolt = <900000>;
|
||
|
|
regulator-ramp-delay = <6001>;
|
||
|
|
regulator-initial-mode = <0x2>;
|
||
|
|
regulator-name = "vdd_gpu";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc_ddr: DCDC_REG3 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-initial-mode = <0x2>;
|
||
|
|
regulator-name = "vcc_ddr";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-on-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vdd_npu: DCDC_REG4 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <500000>;
|
||
|
|
regulator-max-microvolt = <1350000>;
|
||
|
|
regulator-init-microvolt = <900000>;
|
||
|
|
regulator-ramp-delay = <6001>;
|
||
|
|
regulator-initial-mode = <0x2>;
|
||
|
|
regulator-name = "vdd_npu";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vdda0v9_image: LDO_REG1 {
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-min-microvolt = <900000>;
|
||
|
|
regulator-max-microvolt = <900000>;
|
||
|
|
regulator-name = "vdda0v9_image";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vdda_0v9: LDO_REG2 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <900000>;
|
||
|
|
regulator-max-microvolt = <900000>;
|
||
|
|
regulator-name = "vdda_0v9";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vdda0v9_pmu: LDO_REG3 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <900000>;
|
||
|
|
regulator-max-microvolt = <900000>;
|
||
|
|
regulator-name = "vdda0v9_pmu";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-on-in-suspend;
|
||
|
|
regulator-suspend-microvolt = <900000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vccio_acodec: LDO_REG4 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <3000000>;
|
||
|
|
regulator-max-microvolt = <3000000>;
|
||
|
|
regulator-name = "vccio_acodec";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vccio_sd: LDO_REG5 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-name = "vccio_sd";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc3v3_pmu: LDO_REG6 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-name = "vcc3v3_pmu";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-on-in-suspend;
|
||
|
|
regulator-suspend-microvolt = <3300000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vcca_1v8: LDO_REG7 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
regulator-name = "vcca_1v8";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vcca1v8_pmu: LDO_REG8 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
regulator-name = "vcca1v8_pmu";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-on-in-suspend;
|
||
|
|
regulator-suspend-microvolt = <1800000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vcca1v8_image: LDO_REG9 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
regulator-name = "vcca1v8_image";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc_1v8: DCDC_REG5 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
regulator-name = "vcc_1v8";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc_3v3: SWITCH_REG1 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-name = "vcc_3v3";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc3v3_sd: SWITCH_REG2 {
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-name = "vcc3v3_sd";
|
||
|
|
regulator-state-mem {
|
||
|
|
regulator-off-in-suspend;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
codec {
|
||
|
|
mic-in-differential;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&i2s0_8ch {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&i2s1_8ch {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&i2s1m0_sclktx
|
||
|
|
&i2s1m0_lrcktx
|
||
|
|
&i2s1m0_sdi0
|
||
|
|
&i2s1m0_sdo0>;
|
||
|
|
rockchip,trcm-sync-tx-only;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&mdio1 {
|
||
|
|
rgmii_phy0: phy@0 {
|
||
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
||
|
|
reg = <0x0>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&pcie2x1 {
|
||
|
|
reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||
|
|
vpcie3v3-supply = <&vcc3v3_pcie>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&pinctrl {
|
||
|
|
wireless-bluetooth {
|
||
|
|
uart1_gpios: uart1-gpios {
|
||
|
|
rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
sd {
|
||
|
|
sdmmc0_pwr_h: sdmmc0-pwr-h {
|
||
|
|
rockchip,pins =
|
||
|
|
<0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
mxc6655xa {
|
||
|
|
mxc6655xa_irq_gpio: mxc6655xa_irq_gpio {
|
||
|
|
rockchip,pins = <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
pmic {
|
||
|
|
pmic_int: pmic_int {
|
||
|
|
rockchip,pins =
|
||
|
|
<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
|
||
|
|
};
|
||
|
|
|
||
|
|
soc_slppin_gpio: soc_slppin_gpio {
|
||
|
|
rockchip,pins =
|
||
|
|
<0 RK_PA2 RK_FUNC_GPIO &pcfg_output_low>;
|
||
|
|
};
|
||
|
|
|
||
|
|
soc_slppin_slp: soc_slppin_slp {
|
||
|
|
rockchip,pins =
|
||
|
|
<0 RK_PA2 1 &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
|
||
|
|
soc_slppin_rst: soc_slppin_rst {
|
||
|
|
rockchip,pins =
|
||
|
|
<0 RK_PA2 2 &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
touch {
|
||
|
|
touch_gpio: touch-gpio {
|
||
|
|
rockchip,pins =
|
||
|
|
<0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
|
||
|
|
<0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
sdio-pwrseq {
|
||
|
|
wifi_enable_h: wifi-enable-h {
|
||
|
|
rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
usb {
|
||
|
|
vcc5v0_host_en: vcc5v0-host-en {
|
||
|
|
rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
|
||
|
|
vcc5v0_otg_en: vcc5v0-otg-en {
|
||
|
|
rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
wireless-bluetooth {
|
||
|
|
uart8_gpios: uart8-gpios {
|
||
|
|
rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
work-led {
|
||
|
|
leds_gpio: leds-gpio {
|
||
|
|
rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
headphone {
|
||
|
|
hp_det: hp-det {
|
||
|
|
rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
pcie {
|
||
|
|
pcie_drv: pcie-drv {
|
||
|
|
rockchip,pins =
|
||
|
|
<0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
edp {
|
||
|
|
edp_hpd: edp-hpd {
|
||
|
|
rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
|
||
|
|
};
|
||
|
|
|
||
|
|
bl_en: bl-en {
|
||
|
|
rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_output_high>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/*
|
||
|
|
* There are 10 independent IO domains in RK3566/RK3568, including PMUIO[0:2] and VCCIO[1:7].
|
||
|
|
* 1/ PMUIO0 and PMUIO1 are fixed-level power domains which cannot be configured;
|
||
|
|
* 2/ PMUIO2 and VCCIO1,VCCIO[3:7] domains require that their hardware power supply voltages
|
||
|
|
* must be consistent with the software configuration correspondingly
|
||
|
|
* a/ When the hardware IO level is connected to 1.8V, the software voltage configuration
|
||
|
|
* should also be configured to 1.8V accordingly;
|
||
|
|
* b/ When the hardware IO level is connected to 3.3V, the software voltage configuration
|
||
|
|
* should also be configured to 3.3V accordingly;
|
||
|
|
* 3/ VCCIO2 voltage control selection (0xFDC20140)
|
||
|
|
* BIT[0]: 0x0: from GPIO_0A7 (default)
|
||
|
|
* BIT[0]: 0x1: from GRF
|
||
|
|
* Default is determined by Pin FLASH_VOL_SEL/GPIO0_A7:
|
||
|
|
* L:VCCIO2 must supply 3.3V
|
||
|
|
* H:VCCIO2 must supply 1.8V
|
||
|
|
*/
|
||
|
|
|
||
|
|
&pmu_io_domains {
|
||
|
|
status = "okay";
|
||
|
|
pmuio1-supply = <&vcc3v3_pmu>;
|
||
|
|
pmuio2-supply = <&vcc3v3_pmu>;
|
||
|
|
vccio1-supply = <&vcc_3v3>;
|
||
|
|
vccio2-supply = <&vcc_1v8>;
|
||
|
|
vccio3-supply = <&vccio_sd>;
|
||
|
|
vccio4-supply = <&vcc_1v8>;
|
||
|
|
vccio5-supply = <&vcc_3v3>;
|
||
|
|
vccio6-supply = <&vcc_3v3>;
|
||
|
|
vccio7-supply = <&vcc_3v3>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&pwm7 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&saradc {
|
||
|
|
status = "okay";
|
||
|
|
vref-supply = <&vcca_1v8>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&sdhci {
|
||
|
|
bus-width = <8>;
|
||
|
|
max-frequency = <200000000>;
|
||
|
|
non-removable;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&sdmmc0 {
|
||
|
|
max-frequency = <150000000>;
|
||
|
|
bus-width = <4>;
|
||
|
|
cap-mmc-highspeed;
|
||
|
|
cap-sd-highspeed;
|
||
|
|
disable-wp;
|
||
|
|
sd-uhs-sdr104;
|
||
|
|
vmmc-supply = <&vcc_sd>;
|
||
|
|
vqmmc-supply = <&vccio_sd>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&sdmmc1 {
|
||
|
|
max-frequency = <150000000>;
|
||
|
|
bus-width = <4>;
|
||
|
|
disable-wp;
|
||
|
|
cap-sd-highspeed;
|
||
|
|
cap-sdio-irq;
|
||
|
|
keep-power-in-suspend;
|
||
|
|
mmc-pwrseq = <&sdio_pwrseq>;
|
||
|
|
non-removable;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
|
||
|
|
sd-uhs-sdr104;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&sfc {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
status = "okay";
|
||
|
|
flash@0 {
|
||
|
|
compatible = "jedec,spi-nor";
|
||
|
|
reg = <0>;
|
||
|
|
spi-max-frequency = <100000000>;
|
||
|
|
spi-rx-bus-width = <4>;
|
||
|
|
spi-tx-bus-width = <1>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&tsadc {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&uart1 {
|
||
|
|
status = "okay";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb2phy0 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb2phy0_host {
|
||
|
|
phy-supply = <&vbus>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb2phy0_otg {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb2phy1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb2phy1_host {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb2phy1_otg {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb_host0_ehci {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb_host0_ohci {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb_host0_xhci {
|
||
|
|
dr_mode = "host";
|
||
|
|
extcon = <&usb2phy0>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb_host1_ehci {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb_host1_ohci {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb_host1_xhci {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&vop {
|
||
|
|
assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
|
||
|
|
assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&vop_mmu {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&vp0 {
|
||
|
|
vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
|
||
|
|
reg = <ROCKCHIP_VOP2_EP_HDMI0>;
|
||
|
|
remote-endpoint = <&hdmi_in_vp0>;
|
||
|
|
};
|
||
|
|
};
|