842 lines
20 KiB
Diff
842 lines
20 KiB
Diff
|
From 0df42d81eedf9af6b7962c236b88fa9954a83953 Mon Sep 17 00:00:00 2001
|
|||
|
|
From: Ondrej Jirman <megi@xff.cz>
|
|||
|
|
Date: Sat, 10 Jun 2023 18:15:24 +0200
|
|||
|
|
Subject: [PATCH 455/464] arm64: dts: rk3588-orange-pi-5-plus: Add board device
|
|||
|
|
tree
|
|||
|
|
MIME-Version: 1.0
|
|||
|
|
Content-Type: text/plain; charset=UTF-8
|
|||
|
|
Content-Transfer-Encoding: 8bit
|
|||
|
|
|
|||
|
|
Orange Pi 5 Plus is RK3588 based SBC featuring:
|
|||
|
|
|
|||
|
|
- 2x 2.5G ethernet ports – onboard NIC hooked to PCIe 2.0 interface
|
|||
|
|
- 2x USB 2.0 host ports
|
|||
|
|
- 2x USB 3.0 host ports (exposed over USB 3.0 hub)
|
|||
|
|
- Type-C port featuring USB 2.0/3.0 and Alt-DP mode
|
|||
|
|
- PCIe 2.0/USB 2.0/I2S/I2C/UART on E.KEY socket
|
|||
|
|
- RTC
|
|||
|
|
- ES8388 on-board sound codec – jack in/out, onboard mic, speaker amplifier
|
|||
|
|
- SPI NOR flash
|
|||
|
|
- RGB LED (R is always on)
|
|||
|
|
- IR receiver
|
|||
|
|
- PCIe 3.0 on the bottom for NVMe, etc.
|
|||
|
|
- 40pin GPIO header (with gpio, I2C, SPI, PWM, UART)
|
|||
|
|
- Power, recovery and Mask ROM buttons
|
|||
|
|
- 2x HDMI out, 1x HDMI in
|
|||
|
|
- Slots/connectors for eMMC, uSD card, fan, MIPI CSI/DSI
|
|||
|
|
|
|||
|
|
Signed-off-by: Ondrej Jirman <megi@xff.cz>
|
|||
|
|
---
|
|||
|
|
arch/arm64/boot/dts/rockchip/Makefile | 1 +
|
|||
|
|
.../dts/rockchip/rk3588-orangepi-5-plus.dts | 786 ++++++++++++++++++
|
|||
|
|
2 files changed, 787 insertions(+)
|
|||
|
|
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
|
|||
|
|
|
|||
|
|
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
|
|||
|
|
index b7fb908eb92d..8853332840c1 100644
|
|||
|
|
--- a/arch/arm64/boot/dts/rockchip/Makefile
|
|||
|
|
+++ b/arch/arm64/boot/dts/rockchip/Makefile
|
|||
|
|
@@ -98,6 +98,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
|
|||
|
|
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb
|
|||
|
|
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb
|
|||
|
|
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb
|
|||
|
|
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-orangepi-5-plus.dtb
|
|||
|
|
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b.dtb
|
|||
|
|
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-indiedroid-nova.dtb
|
|||
|
|
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-khadas-edge2.dtb
|
|||
|
|
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts b/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
|
|||
|
|
new file mode 100644
|
|||
|
|
index 000000000000..48caf4c38974
|
|||
|
|
--- /dev/null
|
|||
|
|
+++ b/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
|
|||
|
|
@@ -0,0 +1,786 @@
|
|||
|
|
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|||
|
|
+/*
|
|||
|
|
+ * Copyright (c) 2023 Ondřej Jirman <megi@xff.cz>
|
|||
|
|
+ */
|
|||
|
|
+
|
|||
|
|
+/dts-v1/;
|
|||
|
|
+
|
|||
|
|
+#include <dt-bindings/gpio/gpio.h>
|
|||
|
|
+#include <dt-bindings/pinctrl/rockchip.h>
|
|||
|
|
+#include <dt-bindings/leds/common.h>
|
|||
|
|
+#include <dt-bindings/input/input.h>
|
|||
|
|
+#include <dt-bindings/usb/pd.h>
|
|||
|
|
+#include "rk3588.dtsi"
|
|||
|
|
+
|
|||
|
|
+/ {
|
|||
|
|
+ model = "Xunlong Orange Pi 5 Plus";
|
|||
|
|
+ compatible = "xunlong,orangepi-5-plus", "rockchip,rk3588";
|
|||
|
|
+
|
|||
|
|
+ aliases {
|
|||
|
|
+ mmc0 = &sdhci;
|
|||
|
|
+ mmc1 = &sdmmc;
|
|||
|
|
+ serial2 = &uart2;
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ chosen {
|
|||
|
|
+ stdout-path = "serial2:1500000n8";
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ adc-keys0 {
|
|||
|
|
+ compatible = "adc-keys";
|
|||
|
|
+ io-channels = <&saradc 0>;
|
|||
|
|
+ io-channel-names = "buttons";
|
|||
|
|
+ keyup-threshold-microvolt = <1800000>;
|
|||
|
|
+ poll-interval = <100>;
|
|||
|
|
+
|
|||
|
|
+ maskrom-key {
|
|||
|
|
+ linux,code = <KEY_SETUP>;
|
|||
|
|
+ label = "Mask Rom";
|
|||
|
|
+ press-threshold-microvolt = <2000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ adc-keys1 {
|
|||
|
|
+ compatible = "adc-keys";
|
|||
|
|
+ io-channels = <&saradc 1>;
|
|||
|
|
+ io-channel-names = "buttons";
|
|||
|
|
+ keyup-threshold-microvolt = <1800000>;
|
|||
|
|
+ poll-interval = <100>;
|
|||
|
|
+
|
|||
|
|
+ recovery-key {
|
|||
|
|
+ linux,code = <KEY_VENDOR>;
|
|||
|
|
+ label = "Recovery";
|
|||
|
|
+ press-threshold-microvolt = <2000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ speaker_amp: audio-amplifier0 {
|
|||
|
|
+ compatible = "simple-audio-amplifier";
|
|||
|
|
+ enable-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ sound-name-prefix = "Speaker Amp";
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ headphone_amp: audio-amplifier1 {
|
|||
|
|
+ compatible = "simple-audio-amplifier";
|
|||
|
|
+ enable-gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ sound-name-prefix = "Headphones Amp";
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ ir-receiver {
|
|||
|
|
+ compatible = "gpio-ir-receiver";
|
|||
|
|
+ gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>;
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&ir_receiver_pin>;
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ leds {
|
|||
|
|
+ compatible = "gpio-leds";
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&led_pins>;
|
|||
|
|
+
|
|||
|
|
+ led-0 {
|
|||
|
|
+ color = <LED_COLOR_ID_GREEN>;
|
|||
|
|
+ function = LED_FUNCTION_INDICATOR;
|
|||
|
|
+ gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ led-1 {
|
|||
|
|
+ color = <LED_COLOR_ID_BLUE>;
|
|||
|
|
+ function = LED_FUNCTION_INDICATOR;
|
|||
|
|
+ gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ sound {
|
|||
|
|
+ compatible = "simple-audio-card";
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&hp_detect>;
|
|||
|
|
+ simple-audio-card,name = "Analog";
|
|||
|
|
+ simple-audio-card,aux-devs = <&speaker_amp>, <&headphone_amp>;
|
|||
|
|
+ simple-audio-card,format = "i2s";
|
|||
|
|
+ simple-audio-card,mclk-fs = <256>;
|
|||
|
|
+ simple-audio-card,hp-det-gpio = <&gpio1 RK_PD3 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ simple-audio-card,bitclock-master = <&daicpu>;
|
|||
|
|
+ simple-audio-card,frame-master = <&daicpu>;
|
|||
|
|
+
|
|||
|
|
+ simple-audio-card,widgets =
|
|||
|
|
+ "Microphone", "Onboard Microphone",
|
|||
|
|
+ "Microphone", "Microphone Jack",
|
|||
|
|
+ "Speaker", "Speaker",
|
|||
|
|
+ "Headphone", "Headphones";
|
|||
|
|
+
|
|||
|
|
+ simple-audio-card,routing =
|
|||
|
|
+ "Headphones", "LOUT1",
|
|||
|
|
+ "Headphones", "ROUT1",
|
|||
|
|
+ "Speaker", "LOUT2",
|
|||
|
|
+ "Speaker", "ROUT2",
|
|||
|
|
+
|
|||
|
|
+ "Headphones", "Headphones Amp OUTL",
|
|||
|
|
+ "Headphones", "Headphones Amp OUTR",
|
|||
|
|
+ "Headphones Amp INL", "LOUT1",
|
|||
|
|
+ "Headphones Amp INR", "ROUT1",
|
|||
|
|
+
|
|||
|
|
+ "Speaker", "Speaker Amp OUTL",
|
|||
|
|
+ "Speaker", "Speaker Amp OUTR",
|
|||
|
|
+ "Speaker Amp INL", "LOUT2",
|
|||
|
|
+ "Speaker Amp INR", "ROUT2",
|
|||
|
|
+
|
|||
|
|
+ /* single ended signal to LINPUT1 */
|
|||
|
|
+ "LINPUT1", "Microphone Jack",
|
|||
|
|
+ "RINPUT1", "Microphone Jack",
|
|||
|
|
+ /* differential signal */
|
|||
|
|
+ "LINPUT2", "Onboard Microphone",
|
|||
|
|
+ "RINPUT2", "Onboard Microphone";
|
|||
|
|
+
|
|||
|
|
+ daicpu: simple-audio-card,cpu {
|
|||
|
|
+ sound-dai = <&i2s0_8ch>;
|
|||
|
|
+ system-clock-frequency = <12288000>;
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ daicodec: simple-audio-card,codec {
|
|||
|
|
+ sound-dai = <&es8388>;
|
|||
|
|
+ system-clock-frequency = <12288000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ //XXX: this is ethernet_power in schematic, but doesn't enable anything?
|
|||
|
|
+ vcc3v3_pcie_eth: vcc3v3-pcie-eth {
|
|||
|
|
+ compatible = "regulator-fixed";
|
|||
|
|
+ regulator-name = "vcc3v3_pcie_eth";
|
|||
|
|
+ regulator-min-microvolt = <3300000>;
|
|||
|
|
+ regulator-max-microvolt = <3300000>;
|
|||
|
|
+ gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
|
|||
|
|
+ startup-delay-us = <50000>;
|
|||
|
|
+ vin-supply = <&vcc5v0_sys>;
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vcc3v3_pcie30: vcc3v3-pcie30 {
|
|||
|
|
+ compatible = "regulator-fixed";
|
|||
|
|
+ regulator-name = "vcc3v3_pcie30";
|
|||
|
|
+ regulator-min-microvolt = <3300000>;
|
|||
|
|
+ regulator-max-microvolt = <3300000>;
|
|||
|
|
+ enable-active-high;
|
|||
|
|
+ gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ startup-delay-us = <5000>;
|
|||
|
|
+ vin-supply = <&vcc5v0_sys>;
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vcc3v3_wf: vcc3v3-wf {
|
|||
|
|
+ compatible = "regulator-fixed";
|
|||
|
|
+ regulator-name = "vcc3v3_wf";
|
|||
|
|
+ regulator-min-microvolt = <3300000>;
|
|||
|
|
+ regulator-max-microvolt = <3300000>;
|
|||
|
|
+ enable-active-high;
|
|||
|
|
+ gpios = <&gpio2 RK_PC5 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ startup-delay-us = <50000>;
|
|||
|
|
+ vin-supply = <&vcc5v0_sys>;
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vcc5v0_sys: vcc5v0-sys-regulator {
|
|||
|
|
+ compatible = "regulator-fixed";
|
|||
|
|
+ regulator-name = "vcc5v0_sys";
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <5000000>;
|
|||
|
|
+ regulator-max-microvolt = <5000000>;
|
|||
|
|
+ };
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&combphy0_ps {
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&combphy1_ps {
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&combphy2_psu {
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&cpu_b0 {
|
|||
|
|
+ cpu-supply = <&vdd_cpu_big0_s0>;
|
|||
|
|
+ mem-supply = <&vdd_cpu_big0_mem_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&cpu_b1 {
|
|||
|
|
+ cpu-supply = <&vdd_cpu_big0_s0>;
|
|||
|
|
+ mem-supply = <&vdd_cpu_big0_mem_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&cpu_b2 {
|
|||
|
|
+ cpu-supply = <&vdd_cpu_big1_s0>;
|
|||
|
|
+ mem-supply = <&vdd_cpu_big1_mem_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&cpu_b3 {
|
|||
|
|
+ cpu-supply = <&vdd_cpu_big1_s0>;
|
|||
|
|
+ mem-supply = <&vdd_cpu_big1_mem_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&cpu_l0 {
|
|||
|
|
+ cpu-supply = <&vdd_cpu_lit_s0>;
|
|||
|
|
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&cpu_l1 {
|
|||
|
|
+ cpu-supply = <&vdd_cpu_lit_s0>;
|
|||
|
|
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&cpu_l2 {
|
|||
|
|
+ cpu-supply = <&vdd_cpu_lit_s0>;
|
|||
|
|
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&cpu_l3 {
|
|||
|
|
+ cpu-supply = <&vdd_cpu_lit_s0>;
|
|||
|
|
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&i2c0 {
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&i2c0m2_xfer>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+
|
|||
|
|
+ vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: regulator@42 {
|
|||
|
|
+ compatible = "rockchip,rk8602";
|
|||
|
|
+ reg = <0x42>;
|
|||
|
|
+ fcs,suspend-voltage-selector = <1>;
|
|||
|
|
+ regulator-name = "vdd_cpu_big0_s0";
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <550000>;
|
|||
|
|
+ regulator-max-microvolt = <1050000>;
|
|||
|
|
+ regulator-ramp-delay = <2300>;
|
|||
|
|
+ vin-supply = <&vcc5v0_sys>;
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: regulator@43 {
|
|||
|
|
+ compatible = "rockchip,rk8603", "rockchip,rk8602";
|
|||
|
|
+ reg = <0x43>;
|
|||
|
|
+ fcs,suspend-voltage-selector = <1>;
|
|||
|
|
+ regulator-name = "vdd_cpu_big1_s0";
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <550000>;
|
|||
|
|
+ regulator-max-microvolt = <1050000>;
|
|||
|
|
+ regulator-ramp-delay = <2300>;
|
|||
|
|
+ vin-supply = <&vcc5v0_sys>;
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&i2c6 {
|
|||
|
|
+ clock-frequency = <400000>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+
|
|||
|
|
+ hym8563: rtc@51 {
|
|||
|
|
+ compatible = "haoyu,hym8563";
|
|||
|
|
+ reg = <0x51>;
|
|||
|
|
+ #clock-cells = <0>;
|
|||
|
|
+ clock-output-names = "hym8563";
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&hym8563_int>;
|
|||
|
|
+ interrupt-parent = <&gpio0>;
|
|||
|
|
+ interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
|
|||
|
|
+ wakeup-source;
|
|||
|
|
+ };
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&i2c7 {
|
|||
|
|
+ status = "okay";
|
|||
|
|
+
|
|||
|
|
+ es8388: audio-codec@11 {
|
|||
|
|
+ compatible = "everest,es8388";
|
|||
|
|
+ reg = <0x11>;
|
|||
|
|
+ clocks = <&cru I2S0_8CH_MCLKOUT>;
|
|||
|
|
+ clock-names = "mclk";
|
|||
|
|
+ assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
|
|||
|
|
+ assigned-clock-rates = <12288000>;
|
|||
|
|
+ #sound-dai-cells = <0>;
|
|||
|
|
+ };
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&i2s0_8ch {
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&i2s0_lrck
|
|||
|
|
+ &i2s0_mclk
|
|||
|
|
+ &i2s0_sclk
|
|||
|
|
+ &i2s0_sdi0
|
|||
|
|
+ &i2s0_sdo0>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&i2s2_2ch {
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&i2s2m0_lrck
|
|||
|
|
+ &i2s2m0_sclk
|
|||
|
|
+ &i2s2m0_sdi
|
|||
|
|
+ &i2s2m0_sdo>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+/* phy1 - M.KEY socket */
|
|||
|
|
+&pcie2x1l0 {
|
|||
|
|
+ reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ vpcie3v3-supply = <&vcc3v3_wf>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+/* phy2 - right ethernet port */
|
|||
|
|
+&pcie2x1l1 {
|
|||
|
|
+ reset-gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ vpcie3v3-supply = <&vcc3v3_pcie_eth>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+/* phy0 - left ethernet port */
|
|||
|
|
+&pcie2x1l2 {
|
|||
|
|
+ reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
|
|||
|
|
+ vpcie3v3-supply = <&vcc3v3_pcie_eth>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&pinctrl {
|
|||
|
|
+ leds {
|
|||
|
|
+ led_pins: led-pins {
|
|||
|
|
+ rockchip,pins = <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
|
|||
|
|
+ <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ hym8563 {
|
|||
|
|
+ hym8563_int: hym8563-int {
|
|||
|
|
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ sound {
|
|||
|
|
+ hp_detect: hp-detect {
|
|||
|
|
+ rockchip,pins = <1 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ ir-receiver {
|
|||
|
|
+ ir_receiver_pin: ir-receiver-pin {
|
|||
|
|
+ rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&saradc {
|
|||
|
|
+ status = "okay";
|
|||
|
|
+ vref-supply = <&vcc_1v8_s0>;
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&sdhci {
|
|||
|
|
+ bus-width = <8>;
|
|||
|
|
+ no-sdio;
|
|||
|
|
+ no-sd;
|
|||
|
|
+ non-removable;
|
|||
|
|
+ max-frequency = <200000000>;
|
|||
|
|
+ mmc-hs400-1_8v;
|
|||
|
|
+ mmc-hs400-enhanced-strobe;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&sdmmc {
|
|||
|
|
+ bus-width = <4>;
|
|||
|
|
+ cap-sd-highspeed;
|
|||
|
|
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
|
|||
|
|
+ disable-wp;
|
|||
|
|
+ max-frequency = <150000000>;
|
|||
|
|
+ no-sdio;
|
|||
|
|
+ no-mmc;
|
|||
|
|
+ sd-uhs-sdr104;
|
|||
|
|
+ vmmc-supply = <&vcc_3v3_s3>;
|
|||
|
|
+ vqmmc-supply = <&vccio_sd_s0>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&sfc {
|
|||
|
|
+ max-freq = <100000000>;
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&fspim1_pins>;
|
|||
|
|
+ #address-cells = <1>;
|
|||
|
|
+ #size-cells = <0>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+
|
|||
|
|
+ spi_flash: spi-flash@0 {
|
|||
|
|
+ #address-cells = <1>;
|
|||
|
|
+ #size-cells = <0>;
|
|||
|
|
+ compatible = "jedec,spi-nor";
|
|||
|
|
+ reg = <0x0>;
|
|||
|
|
+ spi-max-frequency = <100000000>;
|
|||
|
|
+ spi-tx-bus-width = <1>;
|
|||
|
|
+ spi-rx-bus-width = <4>;
|
|||
|
|
+
|
|||
|
|
+ partitions {
|
|||
|
|
+ compatible = "fixed-partitions";
|
|||
|
|
+ #address-cells = <1>;
|
|||
|
|
+ #size-cells = <1>;
|
|||
|
|
+
|
|||
|
|
+ loader@0 {
|
|||
|
|
+ label = "loader";
|
|||
|
|
+ reg = <0x0 0x1000000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&spi2 {
|
|||
|
|
+ status = "okay";
|
|||
|
|
+ assigned-clocks = <&cru CLK_SPI2>;
|
|||
|
|
+ assigned-clock-rates = <200000000>;
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
|
|||
|
|
+ num-cs = <1>;
|
|||
|
|
+
|
|||
|
|
+ pmic@0 {
|
|||
|
|
+ compatible = "rockchip,rk806";
|
|||
|
|
+ spi-max-frequency = <1000000>;
|
|||
|
|
+ reg = <0x0>;
|
|||
|
|
+
|
|||
|
|
+ interrupt-parent = <&gpio0>;
|
|||
|
|
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
|
|||
|
|
+
|
|||
|
|
+ pinctrl-names = "default";
|
|||
|
|
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
|
|||
|
|
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
|
|||
|
|
+
|
|||
|
|
+ vcc1-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc2-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc3-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc4-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc5-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc6-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc7-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc8-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc9-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc10-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
|
|||
|
|
+ vcc12-supply = <&vcc5v0_sys>;
|
|||
|
|
+ vcc13-supply = <&vdd2_ddr_s3>;
|
|||
|
|
+ vcc14-supply = <&vdd2_ddr_s3>;
|
|||
|
|
+ vcca-supply = <&vcc5v0_sys>;
|
|||
|
|
+
|
|||
|
|
+ gpio-controller;
|
|||
|
|
+ #gpio-cells = <2>;
|
|||
|
|
+
|
|||
|
|
+ rockchip,system-power-controller;
|
|||
|
|
+
|
|||
|
|
+ rk806_dvs1_null: dvs1-null-pins {
|
|||
|
|
+ pins = "gpio_pwrctrl2";
|
|||
|
|
+ function = "pin_fun0";
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ rk806_dvs2_null: dvs2-null-pins {
|
|||
|
|
+ pins = "gpio_pwrctrl2";
|
|||
|
|
+ function = "pin_fun0";
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ rk806_dvs3_null: dvs3-null-pins {
|
|||
|
|
+ pins = "gpio_pwrctrl3";
|
|||
|
|
+ function = "pin_fun0";
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ regulators {
|
|||
|
|
+ vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <550000>;
|
|||
|
|
+ regulator-max-microvolt = <950000>;
|
|||
|
|
+ regulator-ramp-delay = <12500>;
|
|||
|
|
+ regulator-name = "vdd_gpu_s0";
|
|||
|
|
+ regulator-enable-ramp-delay = <400>;
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <550000>;
|
|||
|
|
+ regulator-max-microvolt = <950000>;
|
|||
|
|
+ regulator-ramp-delay = <12500>;
|
|||
|
|
+ regulator-name = "vdd_cpu_lit_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_log_s0: dcdc-reg3 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <675000>;
|
|||
|
|
+ regulator-max-microvolt = <825000>;
|
|||
|
|
+ regulator-init-microvolt = <750000>;
|
|||
|
|
+ regulator-ramp-delay = <12500>;
|
|||
|
|
+ regulator-name = "vdd_log_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <750000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <550000>;
|
|||
|
|
+ regulator-max-microvolt = <825000>;
|
|||
|
|
+ regulator-init-microvolt = <775000>;
|
|||
|
|
+ regulator-ramp-delay = <12500>;
|
|||
|
|
+ regulator-name = "vdd_vdenc_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_ddr_s0: dcdc-reg5 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <675000>;
|
|||
|
|
+ regulator-max-microvolt = <900000>;
|
|||
|
|
+ regulator-init-microvolt = <850000>;
|
|||
|
|
+ regulator-ramp-delay = <12500>;
|
|||
|
|
+ regulator-name = "vdd_ddr_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <850000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd2_ddr_s3: dcdc-reg6 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-name = "vdd2_ddr_s3";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-on-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vcc_2v0_pldo_s3: dcdc-reg7 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <2000000>;
|
|||
|
|
+ regulator-max-microvolt = <2000000>;
|
|||
|
|
+ regulator-ramp-delay = <12500>;
|
|||
|
|
+ regulator-name = "vdd_2v0_pldo_s3";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-on-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <2000000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vcc_3v3_s3: dcdc-reg8 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <3300000>;
|
|||
|
|
+ regulator-max-microvolt = <3300000>;
|
|||
|
|
+ regulator-name = "vcc_3v3_s3";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-on-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <3300000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vddq_ddr_s0: dcdc-reg9 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-name = "vddq_ddr_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vcc_1v8_s3: dcdc-reg10 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <1800000>;
|
|||
|
|
+ regulator-max-microvolt = <1800000>;
|
|||
|
|
+ regulator-name = "vcc_1v8_s3";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-on-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <1800000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ avcc_1v8_s0: pldo-reg1 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <1800000>;
|
|||
|
|
+ regulator-max-microvolt = <1800000>;
|
|||
|
|
+ regulator-name = "avcc_1v8_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vcc_1v8_s0: pldo-reg2 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <1800000>;
|
|||
|
|
+ regulator-max-microvolt = <1800000>;
|
|||
|
|
+ regulator-name = "vcc_1v8_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <1800000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ avdd_1v2_s0: pldo-reg3 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <1200000>;
|
|||
|
|
+ regulator-max-microvolt = <1200000>;
|
|||
|
|
+ regulator-name = "avdd_1v2_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vcc_3v3_s0: pldo-reg4 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <3300000>;
|
|||
|
|
+ regulator-max-microvolt = <3300000>;
|
|||
|
|
+ regulator-ramp-delay = <12500>;
|
|||
|
|
+ regulator-name = "vcc_3v3_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vccio_sd_s0: pldo-reg5 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <1800000>;
|
|||
|
|
+ regulator-max-microvolt = <3300000>;
|
|||
|
|
+ regulator-ramp-delay = <12500>;
|
|||
|
|
+ regulator-name = "vccio_sd_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ /*XXX: missing? */
|
|||
|
|
+ pldo6_s3: pldo-reg6 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <1800000>;
|
|||
|
|
+ regulator-max-microvolt = <1800000>;
|
|||
|
|
+ regulator-name = "pldo6_s3";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-on-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <1800000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_0v75_s3: nldo-reg1 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <750000>;
|
|||
|
|
+ regulator-max-microvolt = <750000>;
|
|||
|
|
+ regulator-name = "vdd_0v75_s3";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-on-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <750000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_ddr_pll_s0: nldo-reg2 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <850000>;
|
|||
|
|
+ regulator-max-microvolt = <850000>;
|
|||
|
|
+ regulator-name = "vdd_ddr_pll_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ regulator-suspend-microvolt = <850000>;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ avdd_0v75_s0: nldo-reg3 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ /*
|
|||
|
|
+ * The schematic mentions that actual setting
|
|||
|
|
+ * should be 0.8375V. RK3588 datasheet specifies
|
|||
|
|
+ * maximum as 0.825V. So we set datasheet max
|
|||
|
|
+ * here.
|
|||
|
|
+ */
|
|||
|
|
+ regulator-min-microvolt = <825000>;
|
|||
|
|
+ regulator-max-microvolt = <825000>;
|
|||
|
|
+ regulator-name = "avdd_0v75_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_0v85_s0: nldo-reg4 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <850000>;
|
|||
|
|
+ regulator-max-microvolt = <850000>;
|
|||
|
|
+ regulator-name = "vdd_0v85_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+
|
|||
|
|
+ vdd_0v75_s0: nldo-reg5 {
|
|||
|
|
+ regulator-always-on;
|
|||
|
|
+ regulator-boot-on;
|
|||
|
|
+ regulator-min-microvolt = <750000>;
|
|||
|
|
+ regulator-max-microvolt = <750000>;
|
|||
|
|
+ regulator-name = "vdd_0v75_s0";
|
|||
|
|
+
|
|||
|
|
+ regulator-state-mem {
|
|||
|
|
+ regulator-off-in-suspend;
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+ };
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&tsadc {
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&uart2 {
|
|||
|
|
+ pinctrl-0 = <&uart2m0_xfer>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
+
|
|||
|
|
+&uart9 {
|
|||
|
|
+ pinctrl-0 = <&uart9m0_xfer>;
|
|||
|
|
+ status = "okay";
|
|||
|
|
+};
|
|||
|
|
--
|
|||
|
|
2.34.1
|
|||
|
|
|