From 8616b6789176fb1694b232255f07f2f92dc8438c Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Sun, 12 Nov 2017 02:10:15 +0100 Subject: [PATCH 260/478] misc: modem-power: Power manager for modems This driver allows for powering/resetting devices that are otherwise handled by other subsytems (USB). It also has mechanismsm for polling from userspace on device->SoC wakeup events via GPIO. This is mostly useful for controling modems. The supported modems are: - Quectel EG25 - ZTE MG3732 Signed-off-by: Ondrej Jirman --- drivers/misc/Kconfig | 7 + drivers/misc/Makefile | 1 + drivers/misc/modem-power.c | 1918 ++++++++++++++++++++++++++++++++++++ 3 files changed, 1926 insertions(+) create mode 100644 drivers/misc/modem-power.c diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index 0f5a49fc7c9e..24cb809ae646 100644 --- a/drivers/misc/Kconfig +++ b/drivers/misc/Kconfig @@ -470,6 +470,13 @@ config HISI_HIKEY_USB switching between the dual-role USB-C port and the USB-A host ports using only one USB controller. +config MODEM_POWER + tristate "Modem power/wakeup support for EG25, MG3732, etc." + depends on OF && SERIAL_DEV_BUS && RFKILL + help + This driver provides support for powering up and handling + wakeup signals for various modems. + source "drivers/misc/c2port/Kconfig" source "drivers/misc/eeprom/Kconfig" source "drivers/misc/cb710/Kconfig" diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index a086197af544..f3eaa577a251 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -59,3 +59,4 @@ obj-$(CONFIG_UACCE) += uacce/ obj-$(CONFIG_XILINX_SDFEC) += xilinx_sdfec.o obj-$(CONFIG_HISI_HIKEY_USB) += hisi_hikey_usb.o obj-$(CONFIG_HI6421V600_IRQ) += hi6421v600-irq.o +obj-$(CONFIG_MODEM_POWER) += modem-power.o diff --git a/drivers/misc/modem-power.c b/drivers/misc/modem-power.c new file mode 100644 index 000000000000..5cb4e76c78ef --- /dev/null +++ b/drivers/misc/modem-power.c @@ -0,0 +1,1918 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Modem power control driver. + * + * Ondrej Jirman + * + * How this works + * -------------- + * + * The driver: + * - can be registered as a platform or serial device + * - will use gpios, regulator and (optionally) serial port to control the modem + * - exposes a character device to control the modem power and receive various + * events + * - exposes sysfs interface to control modem power and wakeup + * - supports multiple modem types and instances + * + * Power up/power down: + * - may take a lot of time (eg. ~13-22s powerup, >22s powerdown) + * - happens on a private workqueue under a lock + * - may happen from shutdown hook + * - prevents suspend when powerup/powerdown is in progress + * - is serialized and there's no abort of in-progress operations + * - for specific power sequence see comments in the section for each + * supported modem variant + * - the driver monitors the power status of the modem (optionally) + * and tries to complete the powerdown initiated via AT command + * - the driver tries to detect when the modem is killswitched off + * and updates the driver status to reflect that + * + * Suspend/resume: + * - suspend is blocked if powerup/down is in progress + * - modem can wakeup the host over gpio based IRQ (RI signal) + * - the driver will assert ap_ready after resume finishes + * + * Rfkill: + * - the driver implements a rfkill interface if rfkill gpio is available + */ + +//#define DEBUG + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRIVER_NAME "modem-power" + +enum { + MPWR_REQ_NONE = 0, + MPWR_REQ_RESET, + MPWR_REQ_PWDN, + MPWR_REQ_PWUP, +}; + +struct mpwr_dev; + +struct mpwr_gpio { + const char* name; + unsigned desc_off; + int flags; + bool required; + int irq_flags; + unsigned irq_off; +}; + +#define MPWR_GPIO_DEF(_name, _flags, _req) \ + { .name = #_name, \ + .desc_off = offsetof(struct mpwr_dev, _name##_gpio), \ + .flags = _flags, \ + .required = _req, \ + } + +#define MPWR_GPIO_DEF_IRQ(_name, _flags, _req, _irq_flags) \ + { .name = #_name, \ + .desc_off = offsetof(struct mpwr_dev, _name##_gpio), \ + .flags = _flags, \ + .required = _req, \ + .irq_flags = _irq_flags, \ + .irq_off = offsetof(struct mpwr_dev, _name##_irq), \ + } + +struct mpwr_variant { + int (*power_init)(struct mpwr_dev* mpwr); + int (*power_up)(struct mpwr_dev* mpwr); + int (*power_down)(struct mpwr_dev* mpwr); + int (*reset)(struct mpwr_dev* mpwr); + void (*recv_msg)(struct mpwr_dev *mpwr, const char *msg); + int (*suspend)(struct mpwr_dev *mpwr); + int (*resume)(struct mpwr_dev *mpwr); + const struct mpwr_gpio* gpios; + bool regulator_required; + bool monitor_wakeup; +}; + +struct mpwr_dev { + struct device *dev; + const struct mpwr_variant* variant; + + wait_queue_head_t wait; + + /* serdev */ + struct serdev_device *serdev; + char rcvbuf[4096]; + size_t rcvbuf_fill; + char msg[4096]; + int msg_len; + int msg_ok; + //struct kfifo kfifo; + DECLARE_KFIFO(kfifo, unsigned char, 4096); + + /* power */ + struct regulator *regulator; + + /* outputs */ + struct gpio_desc *enable_gpio; + struct gpio_desc *reset_gpio; + struct gpio_desc *pwrkey_gpio; + struct gpio_desc *sleep_gpio; + struct gpio_desc *dtr_gpio; + struct gpio_desc *host_ready_gpio; + + /* inputs */ + struct gpio_desc *status_gpio; + struct gpio_desc *wakeup_gpio; + int wakeup_irq; + bool status_pwrkey_multiplexed; + + /* config */ + struct cdev cdev; + dev_t major; + + /* rfkill */ + struct rfkill *rfkill; + + /* powerup/dn work queue */ + struct workqueue_struct *wq; + struct work_struct power_work; + struct work_struct finish_pdn_work; + struct mutex modem_lock; + + // change + spinlock_t lock; /* protects last_request */ + int last_request; + ktime_t last_wakeup; + + struct timer_list wd_timer; + struct delayed_work host_ready_work; + + unsigned long flags[1]; +}; + +enum { + /* modem is powered */ + MPWR_F_POWERED, + MPWR_F_POWER_CHANGE_INPROGRESS, + MPWR_F_KILLSWITCHED, + /* we got a wakeup from the modem */ + MPWR_F_GOT_WAKEUP, + /* serdev */ + MPWR_F_RECEIVING_MSG, + /* eg25 */ + MPWR_F_GOT_RDY, + MPWR_F_GOT_PDN, + + /* config options */ + MPWR_F_DUMB_POWERUP, + MPWR_F_WAIT_RDY, + /* file */ + MPWR_F_OPEN, + MPWR_F_OVERFLOW, +}; + +static struct class* mpwr_class; + +static int mpwr_serdev_at_cmd(struct mpwr_dev *mpwr, const char *msg, int timeout_ms); +static int mpwr_serdev_at_cmd_with_retry(struct mpwr_dev *mpwr, const char *msg, + int timeout_ms, int tries); +static int mpwr_serdev_at_cmd_with_retry_ignore_timeout(struct mpwr_dev *mpwr, const char *msg, + int timeout_ms, int tries); + +// {{{ mg2723 variant + +static int mpwr_mg2723_power_init(struct mpwr_dev* mpwr) +{ + // if the device has power applied or doesn't have regulator + // configured (we assume it's always powered) initialize GPIO + // to shut it down initially + if (!mpwr->regulator || regulator_is_enabled(mpwr->regulator)) { + gpiod_set_value(mpwr->enable_gpio, 0); + gpiod_set_value(mpwr->reset_gpio, 1); + } else { + // device is not powered, don't drive the gpios + gpiod_direction_input(mpwr->enable_gpio); + gpiod_direction_input(mpwr->reset_gpio); + } + + return 0; +} + +static int mpwr_mg2723_power_up(struct mpwr_dev* mpwr) +{ + int ret; + + // power up + if (mpwr->regulator) { + ret = regulator_enable(mpwr->regulator); + if (ret < 0) { + dev_err(mpwr->dev, + "can't enable power supply err=%d", ret); + return ret; + } + } + + gpiod_direction_output(mpwr->enable_gpio, 1); + gpiod_direction_output(mpwr->reset_gpio, 1); + msleep(300); + gpiod_set_value(mpwr->reset_gpio, 0); + + return 0; +} + +static int mpwr_mg2723_power_down(struct mpwr_dev* mpwr) +{ + gpiod_set_value(mpwr->enable_gpio, 0); + msleep(50); + + if (mpwr->regulator) { + regulator_disable(mpwr->regulator); + + gpiod_direction_input(mpwr->enable_gpio); + gpiod_direction_input(mpwr->reset_gpio); + } else { + gpiod_set_value(mpwr->reset_gpio, 1); + } + + return 0; +} + +static int mpwr_mg2723_reset(struct mpwr_dev* mpwr) +{ + gpiod_set_value(mpwr->reset_gpio, 1); + msleep(300); + gpiod_set_value(mpwr->reset_gpio, 0); + + return 0; +} + +static const struct mpwr_gpio mpwr_mg2723_gpios[] = { + MPWR_GPIO_DEF(enable, GPIOD_IN, true), + MPWR_GPIO_DEF(reset, GPIOD_IN, true), + MPWR_GPIO_DEF_IRQ(wakeup, GPIOD_IN, true, IRQF_TRIGGER_FALLING), + { }, +}; + +static const struct mpwr_variant mpwr_mg2723_variant = { + .power_init = mpwr_mg2723_power_init, + .power_up = mpwr_mg2723_power_up, + .power_down = mpwr_mg2723_power_down, + .reset = mpwr_mg2723_reset, + .gpios = mpwr_mg2723_gpios, +}; + +// }}} +// {{{ eg25 variant + +static bool mpwr_eg25_qcfg_airplanecontrol_is_ok(const char* v) +{ + return strstarts(v, "1,"); +} + +struct mpwr_eg25_qcfg { + const char* name; + const char* val; + bool (*is_ok)(const char* val); +}; + +static const struct mpwr_eg25_qcfg mpwr_eg25_qcfgs[] = { + //{ "risignaltype", "\"respective\"", }, + { "risignaltype", "\"physical\"", }, + { "urc/ri/ring", "\"pulse\",1,1000,5000,\"off\",1", }, + { "urc/ri/smsincoming", "\"pulse\",1,1", }, + { "urc/ri/other", "\"off\",1,1", }, + { "urc/ri/pin", "uart_ri", }, + { "urc/delay", "0", }, + + //{ "sleep/datactrl", "0,300,1", }, + + { "sleepind/level", "0", }, + { "wakeupin/level", "0", }, + + { "ApRstLevel", "0", }, + { "ModemRstLevel", "0", }, + + // in EG25-G this tries to modify file in /etc (read-only) + // and fails + //{ "dbgctl", "0", }, + + // we don't need AP_READY + { "apready", "0,0,500", }, + + { "airplanecontrol", "1", mpwr_eg25_qcfg_airplanecontrol_is_ok }, +}; + +static char* mpwr_serdev_get_response_value(struct mpwr_dev *mpwr, + const char* prefix) +{ + int off; + + for (off = 0; off < mpwr->msg_len; off += strlen(mpwr->msg + off) + 1) + if (strstarts(mpwr->msg + off, prefix)) + return mpwr->msg + off + strlen(prefix); + + return NULL; +} + +static struct gpio_desc *mpwr_eg25_get_pwrkey_gpio(struct mpwr_dev *mpwr) +{ + if (mpwr->status_pwrkey_multiplexed) + return mpwr->status_gpio; + + return mpwr->pwrkey_gpio; +} + +/* + * Gpio meanings + * ------------- + * + * enable_gpio - 1 = enables RF, 0 = disables RF + * sleep_gpio - 1 = puts modem to sleep, 0 = wakes up the modem (must be 0 + * during poweron) + * reset_gpio - accepts 150-460ms reset pulse (high __|^|__) + * pwrkey_gpio - accepts 100ms-650ms pulse for powerup (high __|^|__) + * 650ms+ pulse for powerdown + * (initiated after pulse ends, pulse may have indefinite + * duration) + * status_gpio - modem power status 0 = powered 1 = unpowered + * wakeup_gpio - "ring indicator" output from the modem + * host_ready_gpio - AP_READY pin - host is ready to receive URCs + * + * (pwrkey may be multiplexed with status_gpio) + * + * Modem behavior + * -------------- + * + * wakeup_gpio (RI): + * - goes high shortly after power is applied (~15ms) + * - goes low when RDY is sent + * + * dtr_gpio + * - when high, modem can sleep if requested + * - H->L will wake up a sleeping modem + * - internal pull-up + * + * ri + * - pulled low when there's URC + * - modem wakes up on URC automatically + * + * - AT+QURCCFG + * - AT+QINDCFG="csq",1 + * - AT+QINDCFG="ring",1 + * - AT+QINDCFG="smsincoming",1 + * - AT+CGREG=0 + * - AT+CREG=0 + * + * - AT+QURCCFG="urcport","uart1" + */ +static int mpwr_eg25_power_up(struct mpwr_dev* mpwr) +{ + struct gpio_desc *pwrkey_gpio = mpwr_eg25_get_pwrkey_gpio(mpwr); + bool wakeup_ok, status_ok; + bool needs_restart = false; + u32 speed = 115200; + int ret, i, off; + ktime_t start; + + clear_bit(MPWR_F_GOT_RDY, mpwr->flags); + + if (regulator_is_enabled(mpwr->regulator)) + dev_warn(mpwr->dev, + "regulator was already enabled during powerup"); + + /* Enable the modem power. */ + ret = regulator_enable(mpwr->regulator); + if (ret < 0) { + dev_err(mpwr->dev, + "can't enable power supply err=%d", ret); + return ret; + } + + /* Drive default gpio signals during powerup */ + gpiod_direction_output(mpwr->host_ready_gpio, 1); + gpiod_direction_output(mpwr->enable_gpio, 1); + gpiod_direction_output(mpwr->sleep_gpio, 0); + gpiod_direction_output(mpwr->reset_gpio, 0); + gpiod_direction_output(pwrkey_gpio, 0); + gpiod_direction_output(mpwr->dtr_gpio, 0); + + /* Wait for powerup. (30ms min. according to datasheet) */ + msleep(50); + + /* Send 200ms pwrkey pulse to initiate poweron */ + gpiod_set_value(pwrkey_gpio, 1); + msleep(200); + gpiod_set_value(pwrkey_gpio, 0); + + /* Switch status key to input, in case it's multiplexed with pwrkey. */ + gpiod_direction_input(mpwr->status_gpio); + + /* open serial console */ + ret = serdev_device_open(mpwr->serdev); + if (ret) { + dev_err(mpwr->dev, "error opening serdev (%d)\n", ret); + goto err_shutdown_noclose; + } + + of_property_read_u32(mpwr->dev->of_node, "current-speed", &speed); + serdev_device_set_baudrate(mpwr->serdev, speed); + serdev_device_set_flow_control(mpwr->serdev, false); + ret = serdev_device_set_parity(mpwr->serdev, SERDEV_PARITY_NONE); + if (ret) { + dev_err(mpwr->dev, "error setting serdev parity (%d)\n", ret); + goto err_shutdown; + } + + /* + * Wait for status/wakeup change, assume good values, if CTS/status + * signals, are not configured. + */ + status_ok = mpwr->status_gpio ? false : true; + wakeup_ok = mpwr->wakeup_gpio ? false : true; + + /* wait up to 10s for status */ + start = ktime_get(); + while (ktime_ms_delta(ktime_get(), start) < 10000) { + if (!wakeup_ok && mpwr->wakeup_gpio && gpiod_get_value(mpwr->wakeup_gpio)) { + dev_info(mpwr->dev, "wakeup ok\n"); + wakeup_ok = true; + } + + if (!status_ok && mpwr->status_gpio && !gpiod_get_value(mpwr->status_gpio)) { + dev_info(mpwr->dev, "status ok\n"); + status_ok = true; + } + + /* modem is ready */ + if (wakeup_ok && status_ok) + break; + + msleep(50); + } + + if (!wakeup_ok) { + dev_err(mpwr->dev, "The modem looks kill-switched\n"); + if (!test_and_set_bit(MPWR_F_KILLSWITCHED, mpwr->flags)) + sysfs_notify(&mpwr->dev->kobj, NULL, "killswitched"); + goto err_shutdown; + } + + if (!status_ok) { + dev_err(mpwr->dev, "The modem didn't report powerup success in time\n"); + goto err_shutdown; + } + + if (test_and_clear_bit(MPWR_F_KILLSWITCHED, mpwr->flags)) + sysfs_notify(&mpwr->dev->kobj, NULL, "killswitched"); + + if (test_bit(MPWR_F_DUMB_POWERUP, mpwr->flags)) + goto powered_up; + + if (test_bit(MPWR_F_WAIT_RDY, mpwr->flags)) { + // wait for RDY for up to 30s + ret = wait_event_timeout(mpwr->wait, + test_bit(MPWR_F_GOT_RDY, mpwr->flags), + msecs_to_jiffies(30000)); + if (ret <= 0) { + dev_err(mpwr->dev, "The modem didn't send RDY in time\n"); + goto err_shutdown; + } + + // configure the link (disable echo) + ret = mpwr_serdev_at_cmd(mpwr, "AT&FE0", 1000); + if (ret) + goto err_shutdown; + } else { + // configure the link (disable echo) + ret = mpwr_serdev_at_cmd_with_retry_ignore_timeout(mpwr, "AT&FE0", 1000, 30); + if (ret) + goto err_shutdown; + } + + /* print firmware version */ + ret = mpwr_serdev_at_cmd_with_retry(mpwr, "AT+QVERSION;+QSUBSYSVER", 1000, 15); + if (ret == 0 && mpwr->msg_len > 0) { + dev_info(mpwr->dev, "===================================================\n"); + for (off = 0; off < mpwr->msg_len; off += strlen(mpwr->msg + off) + 1) + dev_info(mpwr->dev, "%s\n", mpwr->msg + off); + dev_info(mpwr->dev, "===================================================\n"); + } + + /* print ADB key to dmesg */ + ret = mpwr_serdev_at_cmd_with_retry(mpwr, "AT+QADBKEY?", 1000, 15); + if (ret == 0) { + const char *val = mpwr_serdev_get_response_value(mpwr, "+QADBKEY: "); + if (val) + dev_info(mpwr->dev, "ADB KEY is '%s' (you can use it to unlock ADB access to the modem, see https://xnux.eu/devices/feature/modem-pp.html)\n", val); + } + + // check DAI config + ret = mpwr_serdev_at_cmd_with_retry(mpwr, "AT+QDAI?", 1000, 15); + if (ret == 0) { + const char *val = mpwr_serdev_get_response_value(mpwr, "+QDAI: "); + const char *needed_val = NULL; + char buf[128]; + + if (val) { + of_property_read_string(mpwr->dev->of_node, "quectel,qdai", &needed_val); + + if (needed_val && strcmp(needed_val, val)) { + dev_warn(mpwr->dev, "QDAI is '%s' (changing to '%s')\n", val, needed_val); + + /* update qdai */ + snprintf(buf, sizeof buf, "AT+QDAI=%s", needed_val); + ret = mpwr_serdev_at_cmd(mpwr, buf, 5000); + if (ret == 0) + needs_restart = true; + } else { + dev_info(mpwr->dev, "QDAI is '%s'\n", val); + } + } + } + + /* reset the modem, to apply QDAI config if necessary */ + if (needs_restart) { + clear_bit(MPWR_F_GOT_RDY, mpwr->flags); + + mpwr_serdev_at_cmd(mpwr, "AT+CFUN=1,1", 15000); + + // wait for RDY for up to 30s + ret = wait_event_timeout(mpwr->wait, + test_bit(MPWR_F_GOT_RDY, mpwr->flags), + msecs_to_jiffies(30000)); + if (ret <= 0) { + dev_err(mpwr->dev, "The modem didn't send RDY in time\n"); + goto err_shutdown; + } + + // wait until QDAI starts succeeding (then the modem is ready + // to accept the following QCFGs) + ret = mpwr_serdev_at_cmd_with_retry(mpwr, "AT+QDAI?", 1000, 15); + if (ret) + goto err_shutdown; + } + + /* check and update important QCFGs */ + for (i = 0; i < ARRAY_SIZE(mpwr_eg25_qcfgs); i++) { + const char* name = mpwr_eg25_qcfgs[i].name; + const char* needed_val = mpwr_eg25_qcfgs[i].val; + bool (*is_ok)(const char* val) = mpwr_eg25_qcfgs[i].is_ok; + const char *val; + char buf[128]; + + snprintf(buf, sizeof buf, "AT+QCFG=\"%s\"", name); + ret = mpwr_serdev_at_cmd(mpwr, buf, 1000); + if (ret) + continue; + + snprintf(buf, sizeof buf, "+QCFG: \"%s\",", name); + val = mpwr_serdev_get_response_value(mpwr, buf); + if (val) { + if (needed_val && (is_ok ? !is_ok(val) : strcmp(needed_val, val))) { + dev_info(mpwr->dev, "QCFG '%s' is '%s' (changing to '%s')\n", name, val, needed_val); + + /* update qcfg */ + snprintf(buf, sizeof buf, "AT+QCFG=\"%s\",%s", name, needed_val); + ret = mpwr_serdev_at_cmd(mpwr, buf, 1000); + if (ret) + break; /* go to next QCFG */ + } else { + dev_info(mpwr->dev, "QCFG '%s' is '%s'\n", name, val); + } + } + } + + /* setup URC port */ + ret = mpwr_serdev_at_cmd(mpwr, "AT+QURCCFG=\"urcport\",\"usbat\"", 2000); + if (ret) + dev_err(mpwr->dev, "Modem may not report URCs to the right port!\n"); + + /* enable the modem to go to sleep when DTR is low */ + ret = mpwr_serdev_at_cmd(mpwr, "AT+QSCLK=1", 2000); + if (ret) + dev_err(mpwr->dev, "Modem will probably not sleep!\n"); + +powered_up: + gpiod_direction_output(mpwr->dtr_gpio, 1); + + return 0; + +err_shutdown: + serdev_device_close(mpwr->serdev); +err_shutdown_noclose: + dev_warn(mpwr->dev, + "Forcibly cutting off power, data loss may occur.\n"); + gpiod_direction_input(mpwr->enable_gpio); + gpiod_direction_input(mpwr->reset_gpio); + gpiod_direction_input(mpwr->sleep_gpio); + gpiod_direction_input(pwrkey_gpio); + gpiod_direction_input(mpwr->host_ready_gpio); + gpiod_direction_input(mpwr->dtr_gpio); + + regulator_disable(mpwr->regulator); + return -ENODEV; +} + +static int mpwr_eg25_power_down_finish(struct mpwr_dev* mpwr) +{ + struct gpio_desc *pwrkey_gpio = mpwr_eg25_get_pwrkey_gpio(mpwr); + ktime_t start = ktime_get(); + unsigned safety_delay = 30000; + int ret; + + serdev_device_close(mpwr->serdev); + + /* + * This function is called right after POWERED DOWN message is received. + * + * When the modem powers down RI (wakeup) goes low and STATUS goes + * high at the same time. Status is not connected on some boards. + * RI should be inactive during poweroff, but we don't know for sure. + * + * Therfore: + * - wait for STATUS going low + * - in case that's not available wait for RI going low + * - if wakeup seems to go low too soon (< 10s since POWERED DOWN + * message), make sure we wait at least 30s in total, which + * is the manufacturer's safety delay + * + * In addition, some boards have PWRKEY multiplexed with STATUS signal. + * In that case we need to switch STATUS to output high level, as soon + * as it goes low in order to prevent a power-up signal being registered + * by the modem. + */ + + if (mpwr->status_gpio) { + /* wait up to 30s for status */ + while (ktime_ms_delta(ktime_get(), start) < 30000) { + if (gpiod_get_value(mpwr->status_gpio)) { + if (ktime_ms_delta(ktime_get(), start) < 5000) + dev_warn(mpwr->dev, + "STATUS signal is high too soon during powerdown. Modem is already off?\n"); + goto powerdown; + } + + msleep(20); + } + + dev_warn(mpwr->dev, + "STATUS signal didn't go high during shutdown. Modem is still on?\n"); + goto force_powerdown; + } else { + clear_bit(MPWR_F_GOT_WAKEUP, mpwr->flags); + if (!gpiod_get_value(mpwr->wakeup_gpio)) { + dev_warn(mpwr->dev, + "RI signal is low too soon during powerdown, falling back to a fixed safety delay (%d s)\n", + safety_delay / 1000); + msleep(safety_delay); + goto powerdown; + } + + ret = wait_event_timeout(mpwr->wait, + test_bit(MPWR_F_GOT_WAKEUP, mpwr->flags), + msecs_to_jiffies(safety_delay)); + if (ret <= 0) { + dev_warn(mpwr->dev, + "RI signal didn't go low during shutdown, is modem really powering down?\n"); + goto force_powerdown; + } + + /* 12s safety check */ + if (ktime_ms_delta(ktime_get(), start) < 12000) { + unsigned extra_delay = safety_delay - ktime_ms_delta(ktime_get(), start); + + dev_warn(mpwr->dev, + "RI signal did go low surprisingly early during shutdown, adding a safety delay (%d s)\n", + extra_delay / 1000); + msleep(extra_delay); + } + } + +powerdown: + gpiod_direction_input(mpwr->enable_gpio); + gpiod_direction_input(mpwr->reset_gpio); + gpiod_direction_input(mpwr->sleep_gpio); + gpiod_direction_input(pwrkey_gpio); + gpiod_direction_input(mpwr->host_ready_gpio); + gpiod_direction_input(mpwr->dtr_gpio); + + regulator_disable(mpwr->regulator); + + return 0; + +force_powerdown: + dev_warn(mpwr->dev, + "Forcibly cutting off power, data loss may occur.\n"); + goto powerdown; +} + +static int mpwr_eg25_power_down(struct mpwr_dev* mpwr) +{ + struct gpio_desc *pwrkey_gpio = mpwr_eg25_get_pwrkey_gpio(mpwr); + int ret; + + /* Send 800ms pwrkey pulse to initiate powerdown. */ + gpiod_direction_output(pwrkey_gpio, 1); + msleep(800); + gpiod_set_value(pwrkey_gpio, 0); + + /* Switch status key to input, in case it's multiplexed with pwrkey. */ + gpiod_direction_input(mpwr->status_gpio); + + msleep(50); + + // wait for POWERED DOWN message + clear_bit(MPWR_F_GOT_PDN, mpwr->flags); + ret = wait_event_timeout(mpwr->wait, + test_bit(MPWR_F_GOT_PDN, mpwr->flags), + msecs_to_jiffies(7000)); + if (ret <= 0) + dev_warn(mpwr->dev, + "POWERED DOWN message not received, is modem really powering down?\n"); + + return mpwr_eg25_power_down_finish(mpwr); +} + +static void mpwr_finish_pdn_work(struct work_struct *work) +{ + /* + struct mpwr_dev *mpwr = container_of(work, struct mpwr_dev, power_work); + unsigned long flags; + + spin_lock_irqsave(&mpwr->lock, flags); + spin_unlock_irqrestore(&mpwr->lock, flags); + + pm_stay_awake(mpwr->dev); + + mutex_lock(&mpwr->modem_lock); + + mutex_unlock(&mpwr->modem_lock); + + pm_relax(mpwr->dev); + */ +} + +static void mpwr_eg25_receive_msg(struct mpwr_dev *mpwr, const char *msg) +{ + unsigned int msg_len; + + if (!strcmp(msg, "POWERED DOWN")) { + set_bit(MPWR_F_GOT_PDN, mpwr->flags); + wake_up(&mpwr->wait); + + /* + if (mutex_trylock(&mpwr->modem_lock)) { + // if no power op is in progress, this means userspace + // tried to shut the modem down via AT command, finish up + // the job + + pm_stay_awake(mpwr->dev); + + queue_work(mpwr->wq, &mpwr->power_work); + dev_warn(mpwr->dev, "userspace shut down the modem via AT command, finishing the job\n"); + mpwr_eg25_power_down_finish(mpwr); + mutex_unlock(&mpwr->modem_lock); + + pm_relax(mpwr->dev); + } + */ + return; + } + + if (!strcmp(msg, "RDY")) { + // system is ready after powerup + set_bit(MPWR_F_GOT_RDY, mpwr->flags); + wake_up(&mpwr->wait); + return; + } + + if (!test_bit(MPWR_F_OPEN, mpwr->flags)) + return; + + msg_len = strlen(msg); + + if (msg_len + 1 > kfifo_avail(&mpwr->kfifo)) { + if (!test_and_set_bit(MPWR_F_OVERFLOW, mpwr->flags)) + wake_up(&mpwr->wait); + return; + } + + kfifo_in(&mpwr->kfifo, msg, msg_len); + kfifo_in(&mpwr->kfifo, "\n", 1); + wake_up(&mpwr->wait); +} + +static void mpwr_host_ready_work(struct work_struct *work) +{ + struct mpwr_dev *mpwr = container_of(work, struct mpwr_dev, host_ready_work.work); + int ret; + + mutex_lock(&mpwr->modem_lock); + gpiod_direction_output(mpwr->dtr_gpio, 0); + + /* + * We need to give the modem some time to wake up. + */ + msleep(5); + + ret = mpwr_serdev_at_cmd(mpwr, "AT+QCFG=\"urc/cache\",0", 500); + if (ret) + dev_warn(mpwr->dev, + "Failed to disable urc/cache, you may not be able to see URCs\n"); + + gpiod_direction_output(mpwr->dtr_gpio, 1); + mutex_unlock(&mpwr->modem_lock); + + gpiod_direction_output(mpwr->host_ready_gpio, 1); +} + +static int mpwr_eg25_suspend(struct mpwr_dev *mpwr) +{ + int ret; + + cancel_delayed_work_sync(&mpwr->host_ready_work); + + gpiod_direction_output(mpwr->host_ready_gpio, 0); + + mutex_lock(&mpwr->modem_lock); + gpiod_direction_output(mpwr->dtr_gpio, 0); + + msleep(5); + + ret = mpwr_serdev_at_cmd(mpwr, "AT+QCFG=\"urc/cache\",1", 500); + if (ret) + dev_warn(mpwr->dev, + "Failed to enable urc/cache, you may lose URCs during suspend\n"); + + gpiod_direction_output(mpwr->dtr_gpio, 1); + mutex_unlock(&mpwr->modem_lock); + + return 0; +} + +static int mpwr_eg25_resume(struct mpwr_dev *mpwr) +{ + //gpiod_direction_output(mpwr->dtr_gpio, 0); + + // delay disabling URC cache until the whole system is hopefully resumed... + schedule_delayed_work(&mpwr->host_ready_work, msecs_to_jiffies(1000)); + + return 0; +} + +static const struct mpwr_gpio mpwr_eg25_gpios[] = { + MPWR_GPIO_DEF(enable, GPIOD_OUT_HIGH, true), + MPWR_GPIO_DEF(reset, GPIOD_OUT_LOW, true), + MPWR_GPIO_DEF(pwrkey, GPIOD_OUT_LOW, false), + MPWR_GPIO_DEF(dtr, GPIOD_OUT_LOW, true), + MPWR_GPIO_DEF(status, GPIOD_IN, false), + MPWR_GPIO_DEF_IRQ(wakeup, GPIOD_IN, true, + IRQF_TRIGGER_FALLING), + // XXX: not really needed... + MPWR_GPIO_DEF(sleep, GPIOD_OUT_LOW, false), + MPWR_GPIO_DEF(host_ready, GPIOD_OUT_HIGH, false), + { }, +}; + +static const struct mpwr_variant mpwr_eg25_variant = { + .power_up = mpwr_eg25_power_up, + .power_down = mpwr_eg25_power_down, + .recv_msg = mpwr_eg25_receive_msg, + .suspend = mpwr_eg25_suspend, + .resume = mpwr_eg25_resume, + .gpios = mpwr_eg25_gpios, + .regulator_required = true, + .monitor_wakeup = true, +}; + +// }}} +// {{{ generic helpers + +static void mpwr_reset(struct mpwr_dev* mpwr) +{ + struct device *dev = mpwr->dev; + int ret; + + if (!test_bit(MPWR_F_POWERED, mpwr->flags)) { + dev_err(dev, "reset requested but device is not enabled"); + return; + } + + if (!mpwr->reset_gpio) { + dev_err(dev, "reset is not configured for this device"); + return; + } + + if (!mpwr->variant->reset) { + dev_err(dev, "reset requested but not implemented"); + return; + } + + dev_info(dev, "resetting"); + ret = mpwr->variant->reset(mpwr); + if (ret) { + dev_err(dev, "reset failed"); + } +} + +static void mpwr_power_down(struct mpwr_dev* mpwr) +{ + struct device *dev = mpwr->dev; + ktime_t start = ktime_get(); + int ret; + + if (!test_bit(MPWR_F_POWERED, mpwr->flags)) + return; + + if (!mpwr->variant->power_down) { + dev_err(dev, "power down requested but not implemented"); + return; + } + + dev_info(dev, "powering down"); + + set_bit(MPWR_F_POWER_CHANGE_INPROGRESS, mpwr->flags); + sysfs_notify(&mpwr->dev->kobj, NULL, "is_busy"); + + ret = mpwr->variant->power_down(mpwr); + + clear_bit(MPWR_F_POWER_CHANGE_INPROGRESS, mpwr->flags); + sysfs_notify(&mpwr->dev->kobj, NULL, "is_busy"); + + if (ret) { + dev_err(dev, "power down failed"); + } else { + clear_bit(MPWR_F_POWERED, mpwr->flags); + sysfs_notify(&mpwr->dev->kobj, NULL, "powered"); + dev_info(mpwr->dev, "powered down in %lld ms\n", + ktime_ms_delta(ktime_get(), start)); + } +} + +static void mpwr_power_up(struct mpwr_dev* mpwr) +{ + struct device *dev = mpwr->dev; + ktime_t start = ktime_get(); + int ret; + + if (test_bit(MPWR_F_POWERED, mpwr->flags)) + return; + + if (!mpwr->variant->power_up) { + dev_err(dev, "power up requested but not implemented"); + return; + } + + dev_info(dev, "powering up"); + + set_bit(MPWR_F_POWER_CHANGE_INPROGRESS, mpwr->flags); + sysfs_notify(&mpwr->dev->kobj, NULL, "is_busy"); + + ret = mpwr->variant->power_up(mpwr); + + clear_bit(MPWR_F_POWER_CHANGE_INPROGRESS, mpwr->flags); + sysfs_notify(&mpwr->dev->kobj, NULL, "is_busy"); + + if (ret) { + dev_err(dev, "power up failed"); + } else { + set_bit(MPWR_F_POWERED, mpwr->flags); + sysfs_notify(&mpwr->dev->kobj, NULL, "powered"); + dev_info(mpwr->dev, "powered up in %lld ms\n", + ktime_ms_delta(ktime_get(), start)); + } +} + +// }}} +// {{{ chardev + +static int mpwr_release(struct inode *ip, struct file *fp) +{ + struct mpwr_dev* mpwr = fp->private_data; + + clear_bit(MPWR_F_OPEN, mpwr->flags); + + return 0; +} + +static int mpwr_open(struct inode *ip, struct file *fp) +{ + struct mpwr_dev* mpwr = container_of(ip->i_cdev, struct mpwr_dev, cdev); + + fp->private_data = mpwr; + + if (test_and_set_bit(MPWR_F_OPEN, mpwr->flags)) + return -EBUSY; + + nonseekable_open(ip, fp); + return 0; +} + +static ssize_t mpwr_read(struct file *fp, char __user *buf, size_t len, + loff_t *off) +{ + struct mpwr_dev* mpwr = fp->private_data; + int non_blocking = fp->f_flags & O_NONBLOCK; + unsigned int copied; + int ret; + + if (non_blocking && kfifo_is_empty(&mpwr->kfifo)) + return -EWOULDBLOCK; + + ret = wait_event_interruptible(mpwr->wait, + !kfifo_is_empty(&mpwr->kfifo) + || test_bit(MPWR_F_OVERFLOW, mpwr->flags)); + if (ret) + return ret; + + if (test_and_clear_bit(MPWR_F_OVERFLOW, mpwr->flags)) { + if (len < 9) + return -E2BIG; + if (copy_to_user(buf, "OVERFLOW\n", 9)) + return -EFAULT; + return 9; + } + + ret = kfifo_to_user(&mpwr->kfifo, buf, len, &copied); + + return ret ? ret : copied; +} + +static unsigned int mpwr_poll(struct file *fp, poll_table *wait) +{ + struct mpwr_dev* mpwr = fp->private_data; + + poll_wait(fp, &mpwr->wait, wait); + + if (!kfifo_is_empty(&mpwr->kfifo)) + return EPOLLIN | EPOLLRDNORM; + + return 0; +} + +static const struct file_operations mpwr_fops = { + .owner = THIS_MODULE, + .open = mpwr_open, + .release = mpwr_release, + .llseek = noop_llseek, + .read = mpwr_read, + .poll = mpwr_poll, +}; + +// }}} + +static void mpwr_work_handler(struct work_struct *work) +{ + struct mpwr_dev *mpwr = container_of(work, struct mpwr_dev, power_work); + unsigned long flags; + int last_request; + + spin_lock_irqsave(&mpwr->lock, flags); + last_request = mpwr->last_request; + mpwr->last_request = 0; + spin_unlock_irqrestore(&mpwr->lock, flags); + + pm_stay_awake(mpwr->dev); + + mutex_lock(&mpwr->modem_lock); + + if (last_request == MPWR_REQ_RESET) { + mpwr_reset(mpwr); + } else if (last_request == MPWR_REQ_PWDN) { + mpwr_power_down(mpwr); + } else if (last_request == MPWR_REQ_PWUP) { + mpwr_power_up(mpwr); + } + + mutex_unlock(&mpwr->modem_lock); + + pm_relax(mpwr->dev); +} + +static irqreturn_t mpwr_gpio_isr(int irq, void *dev_id) +{ + struct mpwr_dev *mpwr = dev_id; + + if (irq == mpwr->wakeup_irq) { + dev_dbg(mpwr->dev, "wakeup irq\n"); + + set_bit(MPWR_F_GOT_WAKEUP, mpwr->flags); + spin_lock(&mpwr->lock); + mpwr->last_wakeup = ktime_get(); + spin_unlock(&mpwr->lock); + wake_up(&mpwr->wait); + } + + return IRQ_HANDLED; +} + +static void mpwr_wd_timer_fn(struct timer_list *t) +{ + struct mpwr_dev *mpwr = from_timer(mpwr, t, wd_timer); + + if (!mpwr->variant->monitor_wakeup || !test_bit(MPWR_F_POWERED, mpwr->flags)) + return; + + /* + * Monitor wakeup status: + * + * If RI signal is low for too long we assume the user killswitched + * the modem at runtime. + */ + spin_lock(&mpwr->lock); + if (!gpiod_get_value(mpwr->wakeup_gpio)) { + if (ktime_ms_delta(ktime_get(), mpwr->last_wakeup) > 5000) { + if (!test_and_set_bit(MPWR_F_KILLSWITCHED, mpwr->flags)) + sysfs_notify(&mpwr->dev->kobj, NULL, "killswitched"); + wake_up(&mpwr->wait); + dev_warn(mpwr->dev, "modem looks killswitched at runtime!\n"); + } + } + spin_unlock(&mpwr->lock); + + mod_timer(t, jiffies + msecs_to_jiffies(1000)); +} + +// {{{ sysfs + +static ssize_t powered_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + + return scnprintf(buf, PAGE_SIZE, "%u\n", + !!test_bit(MPWR_F_POWERED, mpwr->flags)); +} + +static ssize_t powered_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + unsigned long flags; + bool status; + int ret; + + ret = kstrtobool(buf, &status); + if (ret) + return ret; + + spin_lock_irqsave(&mpwr->lock, flags); + mpwr->last_request = status ? MPWR_REQ_PWUP : MPWR_REQ_PWDN; + spin_unlock_irqrestore(&mpwr->lock, flags); + + queue_work(mpwr->wq, &mpwr->power_work); + + return len; +} + +static ssize_t dumb_powerup_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + + return scnprintf(buf, PAGE_SIZE, "%u\n", + !!test_bit(MPWR_F_DUMB_POWERUP, mpwr->flags)); +} + +static ssize_t dumb_powerup_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + bool val; + int ret; + + ret = kstrtobool(buf, &val); + if (ret) + return ret; + + if (val) + set_bit(MPWR_F_DUMB_POWERUP, mpwr->flags); + else + clear_bit(MPWR_F_DUMB_POWERUP, mpwr->flags); + + return len; +} + +static ssize_t wait_rdy_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + + return scnprintf(buf, PAGE_SIZE, "%u\n", + !!test_bit(MPWR_F_WAIT_RDY, mpwr->flags)); +} + +static ssize_t wait_rdy_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + bool val; + int ret; + + ret = kstrtobool(buf, &val); + if (ret) + return ret; + + if (val) + set_bit(MPWR_F_WAIT_RDY, mpwr->flags); + else + clear_bit(MPWR_F_WAIT_RDY, mpwr->flags); + + return len; +} + +static ssize_t killswitched_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + + return scnprintf(buf, PAGE_SIZE, "%u\n", + !!test_bit(MPWR_F_KILLSWITCHED, mpwr->flags)); +} + +static ssize_t is_busy_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + + return scnprintf(buf, PAGE_SIZE, "%u\n", + !!test_bit(MPWR_F_POWER_CHANGE_INPROGRESS, mpwr->flags)); +} + +static ssize_t hard_reset_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(to_platform_device(dev)); + unsigned long flags; + bool val; + int ret; + + ret = kstrtobool(buf, &val); + if (ret) + return ret; + + if (val) { + spin_lock_irqsave(&mpwr->lock, flags); + mpwr->last_request = MPWR_REQ_RESET; + spin_unlock_irqrestore(&mpwr->lock, flags); + queue_work(mpwr->wq, &mpwr->power_work); + } + + return len; +} + +static DEVICE_ATTR_RW(powered); +static DEVICE_ATTR_RW(dumb_powerup); +static DEVICE_ATTR_RW(wait_rdy); +static DEVICE_ATTR_RO(killswitched); +static DEVICE_ATTR_RO(is_busy); +static DEVICE_ATTR_WO(hard_reset); + +static struct attribute *mpwr_attrs[] = { + &dev_attr_powered.attr, + &dev_attr_dumb_powerup.attr, + &dev_attr_wait_rdy.attr, + &dev_attr_killswitched.attr, + &dev_attr_is_busy.attr, + &dev_attr_hard_reset.attr, + NULL, +}; + +static const struct attribute_group mpwr_group = { + .attrs = mpwr_attrs, +}; + +// }}} +// {{{ rfkill + +static int mpwr_rfkill_set(void *data, bool blocked) +{ + struct mpwr_dev *mpwr = data; + + gpiod_set_value(mpwr->enable_gpio, !blocked); + return 0; +} + +static void mpwr_rfkill_query(struct rfkill *rfkill, void *data) +{ + struct mpwr_dev *mpwr = data; + + rfkill_set_sw_state(rfkill, !gpiod_get_value(mpwr->enable_gpio)); +} + +static const struct rfkill_ops mpwr_rfkill_ops = { + .set_block = mpwr_rfkill_set, + .query = mpwr_rfkill_query, +}; + +// }}} +// {{{ probe + +static int mpwr_probe_generic(struct device *dev, struct mpwr_dev **mpwr_out) +{ + struct mpwr_dev *mpwr; + struct device_node *np = dev->of_node; + struct device *sdev; + const char* cdev_name = NULL; + int ret, i; + + mpwr = devm_kzalloc(dev, sizeof(*mpwr), GFP_KERNEL); + if (!mpwr) + return -ENOMEM; + + mpwr->variant = of_device_get_match_data(dev); + if (!mpwr->variant) + return -EINVAL; + + mpwr->dev = dev; + init_waitqueue_head(&mpwr->wait); + mutex_init(&mpwr->modem_lock); + spin_lock_init(&mpwr->lock); + INIT_WORK(&mpwr->power_work, &mpwr_work_handler); + INIT_WORK(&mpwr->finish_pdn_work, &mpwr_finish_pdn_work); + INIT_DELAYED_WORK(&mpwr->host_ready_work, mpwr_host_ready_work); + INIT_KFIFO(mpwr->kfifo); + set_bit(MPWR_F_WAIT_RDY, mpwr->flags); + + ret = of_property_read_string(np, "char-device-name", &cdev_name); + if (ret) { + dev_err(dev, "char-device-name is not configured"); + return -EINVAL; + } + + mpwr->status_pwrkey_multiplexed = + of_property_read_bool(np, "status-pwrkey-multiplexed"); + + mpwr->regulator = devm_regulator_get_optional(dev, "power"); + if (IS_ERR(mpwr->regulator)) { + ret = PTR_ERR(mpwr->regulator); + if (ret != -ENODEV) { + dev_err(dev, "can't get power supply err=%d", ret); + return ret; + } + + mpwr->regulator = NULL; + } + + if (!mpwr->regulator && mpwr->variant->regulator_required) { + dev_err(dev, "can't get power supply err=%d", -ENODEV); + return -ENODEV; + } + + for (i = 0; mpwr->variant->gpios[i].name; i++) { + const struct mpwr_gpio *io = &mpwr->variant->gpios[i]; + struct gpio_desc **desc = (struct gpio_desc **)((u8*)mpwr + + io->desc_off); + int *irq = (int*)((u8*)mpwr + io->irq_off); + char buf[64]; + + if (io->required) + *desc = devm_gpiod_get(dev, io->name, io->flags); + else + *desc = devm_gpiod_get_optional(dev, io->name, io->flags); + + if (IS_ERR(*desc)) { + dev_err(dev, "can't get %s gpio err=%ld", io->name, + PTR_ERR(*desc)); + return PTR_ERR(*desc); + } + + if (!*desc) + continue; + + if (io->irq_flags == 0 || io->irq_off == 0) + continue; + + *irq = gpiod_to_irq(*desc); + if (*irq <= 0) { + dev_err(dev, "error converting %s gpio to irq: %d", + io->name, ret); + return *irq; + } + + snprintf(buf, sizeof buf, "modem-%s-gpio", io->name); + ret = devm_request_irq(dev, *irq, mpwr_gpio_isr, io->irq_flags, + devm_kstrdup(dev, buf, GFP_KERNEL), mpwr); + if (ret) { + dev_err(dev, "error requesting %s irq: %d", + io->name, ret); + return ret; + } + } + + if (mpwr->status_pwrkey_multiplexed && mpwr->pwrkey_gpio) { + dev_err(dev, "status and pwrkey are multiplexed, but pwrkey defined\n"); + return -EINVAL; + } + + if (mpwr->status_pwrkey_multiplexed && !mpwr->status_gpio) { + dev_err(dev, "status and pwrkey are multiplexed, but status is not defined\n"); + return -EINVAL; + } + + ret = devm_device_add_group(dev, &mpwr_group); + if (ret) + return ret; + + // create char device + ret = alloc_chrdev_region(&mpwr->major, 0, 1, "modem-power"); + if (ret) { + dev_err(dev, "can't allocate chrdev region"); + goto err_disable_regulator; + } + + cdev_init(&mpwr->cdev, &mpwr_fops); + mpwr->cdev.owner = THIS_MODULE; + ret = cdev_add(&mpwr->cdev, mpwr->major, 1); + if (ret) { + dev_err(dev, "can't add cdev"); + goto err_unreg_chrev_region; + } + + sdev = device_create(mpwr_class, dev, mpwr->major, mpwr, cdev_name); + if (IS_ERR(sdev)) { + ret = PTR_ERR(sdev); + goto err_del_cdev; + } + + if (mpwr->wakeup_irq > 0) { + ret = device_init_wakeup(dev, true); + if (ret) { + dev_err(dev, "failed to init wakeup (%d)\n", ret); + goto err_free_dev; + } + } + + if (mpwr->enable_gpio) { + mpwr->rfkill = rfkill_alloc("modem", dev, RFKILL_TYPE_WWAN, + &mpwr_rfkill_ops, mpwr); + if (!mpwr->rfkill) { + dev_err(dev, "failed to alloc rfkill\n"); + ret = -ENOMEM; + goto err_deinit_wakeup; + } + + rfkill_init_sw_state(mpwr->rfkill, false); + + ret = rfkill_register(mpwr->rfkill); + if (ret) { + dev_err(dev, "failed to register rfkill (%d)\n", ret); + goto err_free_rfkill; + } + } + + mpwr->wq = alloc_ordered_workqueue("modem-power", 0); + if (!mpwr->wq) { + ret = -ENOMEM; + dev_err(dev, "failed to allocate workqueue\n"); + goto err_unreg_rfkill; + } + + if (mpwr->variant->power_init) + mpwr->variant->power_init(mpwr); + + timer_setup(&mpwr->wd_timer, mpwr_wd_timer_fn, 0); + mod_timer(&mpwr->wd_timer, jiffies + msecs_to_jiffies(50)); + + dev_info(dev, "modem power manager ready"); + *mpwr_out = mpwr; + + return 0; + +err_unreg_rfkill: + if (mpwr->rfkill) + rfkill_unregister(mpwr->rfkill); +err_free_rfkill: + if (mpwr->rfkill) + rfkill_destroy(mpwr->rfkill); +err_deinit_wakeup: + if (mpwr->wakeup_irq > 0) + device_init_wakeup(dev, false); +err_free_dev: + device_destroy(mpwr_class, mpwr->major); +err_del_cdev: + cdev_del(&mpwr->cdev); +err_unreg_chrev_region: + unregister_chrdev(mpwr->major, "modem-power"); +err_disable_regulator: + cancel_work_sync(&mpwr->power_work); + return ret; +} + +static int mpwr_remove_generic(struct mpwr_dev *mpwr) +{ + if (mpwr->rfkill) { + rfkill_unregister(mpwr->rfkill); + rfkill_destroy(mpwr->rfkill); + } + + if (mpwr->wakeup_irq > 0) + device_init_wakeup(mpwr->dev, false); + + del_timer_sync(&mpwr->wd_timer); + cancel_delayed_work_sync(&mpwr->host_ready_work); + + cancel_work_sync(&mpwr->power_work); + destroy_workqueue(mpwr->wq); + + mutex_lock(&mpwr->modem_lock); + mpwr_power_down(mpwr); + mutex_unlock(&mpwr->modem_lock); + + device_destroy(mpwr_class, mpwr->major); + cdev_del(&mpwr->cdev); + unregister_chrdev(mpwr->major, "modem-power"); + + return 0; +} + +static void mpwr_shutdown_generic(struct mpwr_dev *mpwr) +{ + cancel_work_sync(&mpwr->power_work); + cancel_delayed_work_sync(&mpwr->host_ready_work); + + mutex_lock(&mpwr->modem_lock); + mpwr_power_down(mpwr); + mutex_unlock(&mpwr->modem_lock); +} + +// }}} +// {{{ suspend/resume + +static int __maybe_unused mpwr_suspend(struct device *dev) +{ + struct mpwr_dev *mpwr = dev_get_drvdata(dev); + int ret = 0; + + if (!test_bit(MPWR_F_POWERED, mpwr->flags)) + return 0; + + //if (mpwr->sleep_gpio) + //gpiod_direction_output(mpwr->sleep_gpio, 1); + + if (mpwr->variant->suspend) + mpwr->variant->suspend(mpwr); + + if (mpwr->wakeup_irq && device_may_wakeup(mpwr->dev)) + enable_irq_wake(mpwr->wakeup_irq); + + return ret; +} + +static int __maybe_unused mpwr_resume(struct device *dev) +{ + struct mpwr_dev *mpwr = dev_get_drvdata(dev); + int ret = 0; + + if (!test_bit(MPWR_F_POWERED, mpwr->flags)) + return 0; + + //if (mpwr->sleep_gpio) + //gpiod_direction_output(mpwr->sleep_gpio, 0); + + if (mpwr->variant->resume) + mpwr->variant->resume(mpwr); + + if (mpwr->wakeup_irq && device_may_wakeup(mpwr->dev)) + disable_irq_wake(mpwr->wakeup_irq); + + return ret; +} + +static const struct dev_pm_ops mpwr_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(mpwr_suspend, mpwr_resume) +}; + +// }}} +// {{{ serdev + +static int mpwr_serdev_send_msg(struct mpwr_dev *mpwr, const char *msg) +{ + int ret, len; + char buf[128]; + + if (!mpwr->serdev) + return -ENODEV; + + len = snprintf(buf, sizeof buf, "%s\r\n", msg); + if (len >= sizeof buf) + return -E2BIG; + + ret = serdev_device_write(mpwr->serdev, buf, len, msecs_to_jiffies(3000)); + if (ret < len) + return -EIO; + + serdev_device_wait_until_sent(mpwr->serdev, msecs_to_jiffies(3000)); + + return 0; +} + +static int __mpwr_serdev_at_cmd(struct mpwr_dev *mpwr, const char *msg, + int timeout_ms, bool report_error, bool report_timeout) +{ + int ret; + + if (test_and_set_bit(MPWR_F_RECEIVING_MSG, mpwr->flags)) + return -EBUSY; + + mpwr->msg_len = 0; + + dev_dbg(mpwr->dev, "SEND: %s\n", msg); + + ret = mpwr_serdev_send_msg(mpwr, msg); + if (ret) { + clear_bit(MPWR_F_RECEIVING_MSG, mpwr->flags); + dev_err(mpwr->dev, "AT command '%s' can't be sent (%d)\n", msg, ret); + return ret; + } + + ret = wait_event_interruptible_timeout(mpwr->wait, + !test_bit(MPWR_F_RECEIVING_MSG, mpwr->flags), + msecs_to_jiffies(timeout_ms)); + if (ret <= 0) { + clear_bit(MPWR_F_RECEIVING_MSG, mpwr->flags); + if (report_timeout) + dev_err(mpwr->dev, "AT command '%s' timed out\n", msg); + return ret ? ret : -ETIMEDOUT; + } + + if (!mpwr->msg_ok) { + if (report_error) + dev_err(mpwr->dev, "AT command '%s' returned ERROR\n", msg); + return -EINVAL; + } + + return 0; +} + +static int mpwr_serdev_at_cmd(struct mpwr_dev *mpwr, const char *msg, int timeout_ms) +{ + return __mpwr_serdev_at_cmd(mpwr, msg, timeout_ms, true, true); +} + +static int __mpwr_serdev_at_cmd_with_retry(struct mpwr_dev *mpwr, const char *msg, + int timeout_ms, int tries, bool ignore_timeout) +{ + int ret = 0; + + if (tries < 1) + tries = 1; + + while (tries-- > 0) { + ret = __mpwr_serdev_at_cmd(mpwr, msg, timeout_ms, false, !ignore_timeout); + if (ret != -EINVAL && (!ignore_timeout || ret != -ETIMEDOUT)) + return ret; + + if (ret != -ETIMEDOUT) + msleep(1000); + } + + dev_err(mpwr->dev, "AT command '%s' returned ERROR\n", msg); + return ret; +} + +static int mpwr_serdev_at_cmd_with_retry(struct mpwr_dev *mpwr, const char *msg, + int timeout_ms, int tries) +{ + return __mpwr_serdev_at_cmd_with_retry(mpwr, msg, timeout_ms, tries, false); +} + +static int mpwr_serdev_at_cmd_with_retry_ignore_timeout(struct mpwr_dev *mpwr, const char *msg, + int timeout_ms, int tries) +{ + return __mpwr_serdev_at_cmd_with_retry(mpwr, msg, timeout_ms, tries, true); +} + +static void mpwr_serdev_receive_msg(struct mpwr_dev *mpwr, const char *msg) +{ + dev_dbg(mpwr->dev, "RECV: %s\n", msg); + + if (mpwr->variant->recv_msg) + mpwr->variant->recv_msg(mpwr, msg); + + if (!test_bit(MPWR_F_RECEIVING_MSG, mpwr->flags)) + return; + + if (!strcmp(msg, "OK")) { + clear_bit(MPWR_F_RECEIVING_MSG, mpwr->flags); + mpwr->msg_ok = true; + wake_up(&mpwr->wait); + return; + } else if (!strcmp(msg, "ERROR")) { + clear_bit(MPWR_F_RECEIVING_MSG, mpwr->flags); + mpwr->msg_ok = false; + wake_up(&mpwr->wait); + return; + } else { + int len = strlen(msg); + + if (mpwr->msg_len + len + 1 > sizeof(mpwr->msg)) { + dev_warn(mpwr->dev, "message buffer overflow, ignoring message\n"); + return; + } + + memcpy(mpwr->msg + mpwr->msg_len, msg, len + 1); + mpwr->msg_len += len + 1; + } +} + +static int mpwr_serdev_receive_buf(struct serdev_device *serdev, + const unsigned char *buf, size_t count) +{ + struct mpwr_dev *mpwr = serdev_device_get_drvdata(serdev); + size_t avail = sizeof(mpwr->rcvbuf) - mpwr->rcvbuf_fill; + char* p; + + if (avail < count) + count = avail; + + if (avail > 0) { + memcpy(mpwr->rcvbuf + mpwr->rcvbuf_fill, buf, count); + mpwr->rcvbuf_fill += count; + } + + while (true) { + p = strnstr(mpwr->rcvbuf, "\r\n", mpwr->rcvbuf_fill); + if (p) { + if (p > mpwr->rcvbuf) { + *p = 0; + mpwr_serdev_receive_msg(mpwr, mpwr->rcvbuf); + } + + mpwr->rcvbuf_fill -= (p - mpwr->rcvbuf) + 2; + memmove(mpwr->rcvbuf, p + 2, mpwr->rcvbuf_fill); + } else { + if (sizeof(mpwr->rcvbuf) - mpwr->rcvbuf_fill == 0) { + mpwr->rcvbuf_fill = 0; + dev_warn(mpwr->dev, "rcvbuf overflow\n"); + } + + break; + } + } + + return count; +} + +static const struct serdev_device_ops mpwr_serdev_ops = { + .receive_buf = mpwr_serdev_receive_buf, + .write_wakeup = serdev_device_write_wakeup, +}; + +static int mpwr_serdev_probe(struct serdev_device *serdev) +{ + struct device *dev = &serdev->dev; + struct mpwr_dev* mpwr; + int ret; + + ret = mpwr_probe_generic(dev, &mpwr); + if (ret) + return ret; + + serdev_device_set_drvdata(serdev, mpwr); + serdev_device_set_client_ops(serdev, &mpwr_serdev_ops); + mpwr->serdev = serdev; + + return 0; +} + +static void mpwr_serdev_remove(struct serdev_device *serdev) +{ + struct mpwr_dev *mpwr = serdev_device_get_drvdata(serdev); + + mpwr_remove_generic(mpwr); +} + +static const struct of_device_id mpwr_of_match_serdev[] = { + { .compatible = "quectel,eg25", + .data = &mpwr_eg25_variant }, + {}, +}; +MODULE_DEVICE_TABLE(of, mpwr_of_match_serdev); + +static void mpwr_serdev_shutdown(struct device *dev) +{ + struct mpwr_dev *mpwr = dev_get_drvdata(dev); + + mpwr_shutdown_generic(mpwr); +} + +static struct serdev_device_driver mpwr_serdev_driver = { + .probe = mpwr_serdev_probe, + .remove = mpwr_serdev_remove, + .driver = { + .name = DRIVER_NAME, + .of_match_table = mpwr_of_match_serdev, + .pm = &mpwr_pm_ops, + .shutdown = mpwr_serdev_shutdown, + }, +}; + +// }}} +// {{{ platdev + +static int mpwr_pdev_probe(struct platform_device *pdev) +{ + struct mpwr_dev* mpwr; + int ret; + + ret = mpwr_probe_generic(&pdev->dev, &mpwr); + if (ret) + return ret; + + platform_set_drvdata(pdev, mpwr); + return 0; +} + +static int mpwr_pdev_remove(struct platform_device *pdev) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(pdev); + + return mpwr_remove_generic(mpwr); +} + +static void mpwr_pdev_shutdown(struct platform_device *pdev) +{ + struct mpwr_dev *mpwr = platform_get_drvdata(pdev); + + mpwr_shutdown_generic(mpwr); +} + +static const struct of_device_id mpwr_of_match_plat[] = { + { .compatible = "zte,mg3732", + .data = &mpwr_mg2723_variant }, + {}, +}; +MODULE_DEVICE_TABLE(of, mpwr_of_match_plat); + +static struct platform_driver mpwr_platform_driver = { + .probe = mpwr_pdev_probe, + .remove = mpwr_pdev_remove, + .shutdown = mpwr_pdev_shutdown, + .driver = { + .name = DRIVER_NAME, + .of_match_table = mpwr_of_match_plat, + .pm = &mpwr_pm_ops, + }, +}; + +// }}} +// {{{ driver init + +static int __init mpwr_driver_init(void) +{ + int ret; + + mpwr_class = class_create(THIS_MODULE, "modem-power"); + if (IS_ERR(mpwr_class)) + return PTR_ERR(mpwr_class); + + ret = serdev_device_driver_register(&mpwr_serdev_driver); + if (ret) + goto err_class; + + ret = platform_driver_register(&mpwr_platform_driver); + if (ret) + goto err_serdev; + + return ret; + +err_serdev: + serdev_device_driver_unregister(&mpwr_serdev_driver); +err_class: + class_destroy(mpwr_class); + return ret; +} + +static void __exit mpwr_driver_exit(void) +{ + serdev_device_driver_unregister(&mpwr_serdev_driver); + platform_driver_unregister(&mpwr_platform_driver); + class_destroy(mpwr_class); +} + +module_init(mpwr_driver_init); +module_exit(mpwr_driver_exit); + +MODULE_DESCRIPTION("Modem power manager"); +MODULE_AUTHOR("Ondrej Jirman "); +MODULE_LICENSE("GPL v2"); + +// }}} -- 2.35.3