aixiao/build
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
master
build/patch/kernel/archive/sunxi-6.4/patches.armbian/net-phy-Support-yt8531c.patch

2349 lines
70 KiB
Diff
Raw Permalink Blame History

From fe406b3525eeba3bff82be7a8157254c13739206 Mon Sep 17 00:00:00 2001
From: afaulkner420 <afaulkner420@gmail.com>
Date: Fri, 25 Mar 2022 20:20:34 +0000
Subject: [PATCH 161/170] net: phy: Support yt8531c
---
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 60 +
drivers/net/phy/motorcomm.c | 1561 ++++++++++++++++-
drivers/net/phy/yt8614-phy.h | 491 ++++++
include/linux/motorcomm_phy.h | 119 ++
4 files changed, 2152 insertions(+), 79 deletions(-)
create mode 100644 drivers/net/phy/yt8614-phy.h
create mode 100644 include/linux/motorcomm_phy.h
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index c5f33630e..9f0a33e21 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -143,6 +143,9 @@ static void stmmac_exit_fs(struct net_device *dev);
#define STMMAC_COAL_TIMER(x) (ns_to_ktime((x) * NSEC_PER_USEC))
+#define RTL_8211E_PHY_ID 0x001cc915
+#define RTL_8211F_PHY_ID 0x001cc916
+
int stmmac_bus_clks_config(struct stmmac_priv *priv, bool enabled)
{
int ret = 0;
@@ -6891,6 +6894,54 @@ void stmmac_fpe_handshake(struct stmmac_priv *priv, bool enable)
}
}
+static int phy_rtl8211e_led_fixup(struct phy_device *phydev)
+{
+ //int val;
+
+ printk("%s in\n", __func__);
+
+ /*switch to extension page44*/
+ phy_write(phydev, 31, 0x07);
+ phy_write(phydev, 30, 0x2c);
+
+ /*set led1(yellow) act
+ val = phy_read(phydev, 26);
+ val &= (~(1<<4));// bit4=0
+ val |= (1<<5);// bit5=1
+ val &= (~(1<<6));// bit6=0*/
+ phy_write(phydev, 26, 0x20);
+
+ /*set led0(green) link
+ val = phy_read(phydev, 28);
+ val |= (7<<0);// bit0,1,2=1
+ val &= (~(7<<4));// bit4,5,6=0
+ val &= (~(7<<8));// bit8,9,10=0*/
+ phy_write(phydev, 28, 0x07);
+
+ /*switch back to page0*/
+ phy_write(phydev,31,0x00);
+
+ return 0;
+}
+
+static int phy_rtl8211f_led_fixup(struct phy_device *phydev)
+{
+ printk("%s in\n", __func__);
+
+ /*switch to extension page44*/
+ phy_write(phydev, 31, 0xd04);
+
+ /*set led1(yellow) act */
+ /*set led2(green) link*/
+ phy_write(phydev, 16, 0xae00);
+
+ phy_write(phydev, 17, 0);
+ /*switch back to page0*/
+ phy_write(phydev,31,0x00);
+
+ return 0;
+}
+
/**
* stmmac_dvr_probe
* @device: device pointer
@@ -7150,6 +7201,15 @@ int stmmac_dvr_probe(struct device *device,
goto error_phy_setup;
}
+ /* register the PHY board fixup */
+ ret = phy_register_fixup_for_uid(RTL_8211E_PHY_ID, 0xffffffff, phy_rtl8211e_led_fixup);
+ if (ret)
+ pr_warn("Cannot register PHY board fixup.\n");
+
+ ret = phy_register_fixup_for_uid(RTL_8211F_PHY_ID, 0xffffffff, phy_rtl8211f_led_fixup);
+ if (ret)
+ pr_warn("Cannot register PHY board fixup.\n");
+
ret = register_netdev(ndev);
if (ret) {
dev_err(priv->device, "%s: ERROR %i registering the device\n",
diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index 7e6ac2c5e..c6876bd08 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -1,137 +1,1540 @@
-// SPDX-License-Identifier: GPL-2.0+
/*
+ * drivers/net/phy/motorcomm.c
+ *
* Driver for Motorcomm PHYs
*
- * Author: Peter Geis <pgwipeout@gmail.com>
+ * Author: Leilei Zhao <leilei.zhao@motorcomm.com>
+ *
+ * Copyright (c) 2019 Motorcomm, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * Support : Motorcomm Phys:
+ * Giga phys: yt8511, yt8521
+ * 100/10 Phys : yt8512, yt8512b, yt8510
+ * Automotive 100Mb Phys : yt8010
+ * Automotive 100/10 hyper range Phys: yt8510
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
+#include <linux/motorcomm_phy.h>
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#ifndef LINUX_VERSION_CODE
+#include <linux/version.h>
+#else
+#define KERNEL_VERSION(a,b,c) (((a) << 16) + ((b) << 8) + (c))
+#endif
+/*for wol, 20210604*/
+#include <linux/netdevice.h>
-#define PHY_ID_YT8511 0x0000010a
+#include "yt8614-phy.h"
-#define YT8511_PAGE_SELECT 0x1e
-#define YT8511_PAGE 0x1f
-#define YT8511_EXT_CLK_GATE 0x0c
-#define YT8511_EXT_DELAY_DRIVE 0x0d
-#define YT8511_EXT_SLEEP_CTRL 0x27
+/**** configuration section begin ***********/
-/* 2b00 25m from pll
- * 2b01 25m from xtl *default*
- * 2b10 62.m from pll
- * 2b11 125m from pll
+/* if system depends on ethernet packet to restore from sleep, please define this macro to 1
+ * otherwise, define it to 0.
*/
-#define YT8511_CLK_125M (BIT(2) | BIT(1))
-#define YT8511_PLLON_SLP BIT(14)
+#define SYS_WAKEUP_BASED_ON_ETH_PKT 1
-/* RX Delay enabled = 1.8ns 1000T, 8ns 10/100T */
-#define YT8511_DELAY_RX BIT(0)
+/* to enable system WOL of phy, please define this macro to 1
+ * otherwise, define it to 0.
+ */
+#define YTPHY_ENABLE_WOL 0
-/* TX Gig-E Delay is bits 7:4, default 0x5
- * TX Fast-E Delay is bits 15:12, default 0xf
- * Delay = 150ps * N - 250ps
- * On = 2000ps, off = 50ps
+/* some GMAC need clock input from PHY, for eg., 125M, please enable this macro
+ * by degault, it is set to 0
+ * NOTE: this macro will need macro SYS_WAKEUP_BASED_ON_ETH_PKT to set to 1
*/
-#define YT8511_DELAY_GE_TX_EN (0xf << 4)
-#define YT8511_DELAY_GE_TX_DIS (0x2 << 4)
-#define YT8511_DELAY_FE_TX_EN (0xf << 12)
-#define YT8511_DELAY_FE_TX_DIS (0x2 << 12)
+#define GMAC_CLOCK_INPUT_NEEDED 1
+
+
+#define YT8521_PHY_MODE_FIBER 1 //fiber mode only
+#define YT8521_PHY_MODE_UTP 2 //utp mode only
+#define YT8521_PHY_MODE_POLL 3 //fiber and utp, poll mode
+
+/* please make choice according to system design
+ * for Fiber only system, please define YT8521_PHY_MODE_CURR 1
+ * for UTP only system, please define YT8521_PHY_MODE_CURR 2
+ * for combo system, please define YT8521_PHY_MODE_CURR 3
+ */
+#define YT8521_PHY_MODE_CURR 3
+
+/**** configuration section end ***********/
+
+
+/* no need to change below */
+
+#if (YTPHY_ENABLE_WOL)
+#undef SYS_WAKEUP_BASED_ON_ETH_PKT
+#define SYS_WAKEUP_BASED_ON_ETH_PKT 1
+#endif
-static int yt8511_read_page(struct phy_device *phydev)
+/* workaround for 8521 fiber 100m mode */
+static int link_mode_8521 = 0; //0: no link; 1: utp; 32: fiber. traced that 1000m fiber uses 32.
+static int link_mode_8614[4] = {0}; //0: no link; 1: utp; 32: fiber. traced that 1000m fiber uses 32.
+
+/* for multiple port phy, base phy address */
+static unsigned int yt_mport_base_phy_addr = 0xff; //0xff: invalid; for 8618
+static unsigned int yt_mport_base_phy_addr_8614 = 0xff; //0xff: invalid;
+
+int phy_yt8531_led_fixup(struct mii_bus *bus, int addr);
+int yt8511_config_out_125m(struct mii_bus *bus, int phy_id);
+
+#if ( LINUX_VERSION_CODE > KERNEL_VERSION(5,0,0) )
+int genphy_config_init(struct phy_device *phydev)
{
- return __phy_read(phydev, YT8511_PAGE_SELECT);
-};
+ int ret;
+
+ //printk (KERN_INFO "yzhang..read phyaddr=%d, phyid=%08x\n",phydev->mdio.addr, phydev->phy_id);
+
+ if(phydev->phy_id == 0x4f51e91b)
+ {
+ //printk (KERN_INFO "yzhang..get YT8511, abt to set 125m clk out, phyaddr=%d, phyid=%08x\n",phydev->mdio.addr, phydev->phy_id);
+ ret = yt8511_config_out_125m(phydev->mdio.bus, phydev->mdio.addr);
+ //printk (KERN_INFO "yzhang..8511 set 125m clk out, reg=%#04x\n",phydev->mdio.bus->read(phydev->mdio.bus,phydev->mdio.addr,0x1f)/*double check as delay*/);
+ if (ret<0)
+ printk (KERN_INFO "yzhang..failed to set 125m clk out, ret=%d\n",ret);
-static int yt8511_write_page(struct phy_device *phydev, int page)
+ phy_yt8531_led_fixup(phydev->mdio.bus, phydev->mdio.addr);
+ }
+ return genphy_read_abilities(phydev);
+}
+#endif
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+static int ytphy_config_init(struct phy_device *phydev)
{
- return __phy_write(phydev, YT8511_PAGE_SELECT, page);
-};
+ return 0;
+}
+#endif
+
+static int ytphy_read_ext(struct phy_device *phydev, u32 regnum)
+{
+ int ret;
+ int val;
+
+ ret = phy_write(phydev, REG_DEBUG_ADDR_OFFSET, regnum);
+ if (ret < 0)
+ return ret;
+
+ val = phy_read(phydev, REG_DEBUG_DATA);
+
+ return val;
+}
+
+static int ytphy_write_ext(struct phy_device *phydev, u32 regnum, u16 val)
+{
+ int ret;
+
+ ret = phy_write(phydev, REG_DEBUG_ADDR_OFFSET, regnum);
+ if (ret < 0)
+ return ret;
+
+ ret = phy_write(phydev, REG_DEBUG_DATA, val);
+
+ return ret;
+}
+
+static int yt8010_config_aneg(struct phy_device *phydev)
+{
+ phydev->speed = SPEED_100;
+ return 0;
+}
+
+static int yt8512_clk_init(struct phy_device *phydev)
+{
+ int ret;
+ int val;
+
+ val = ytphy_read_ext(phydev, YT8512_EXTREG_AFE_PLL);
+ if (val < 0)
+ return val;
+
+ val |= YT8512_CONFIG_PLL_REFCLK_SEL_EN;
+
+ ret = ytphy_write_ext(phydev, YT8512_EXTREG_AFE_PLL, val);
+ if (ret < 0)
+ return ret;
+
+ val = ytphy_read_ext(phydev, YT8512_EXTREG_EXTEND_COMBO);
+ if (val < 0)
+ return val;
+
+ val |= YT8512_CONTROL1_RMII_EN;
+
+ ret = ytphy_write_ext(phydev, YT8512_EXTREG_EXTEND_COMBO, val);
+ if (ret < 0)
+ return ret;
+
+ val = phy_read(phydev, MII_BMCR);
+ if (val < 0)
+ return val;
+
+ val |= YT_SOFTWARE_RESET;
+ ret = phy_write(phydev, MII_BMCR, val);
+
+ return ret;
+}
+
+static int yt8512_led_init(struct phy_device *phydev)
+{
+ int ret;
+ int val;
+ int mask;
+
+ val = ytphy_read_ext(phydev, YT8512_EXTREG_LED0);
+ if (val < 0)
+ return val;
+
+ val |= YT8512_LED0_ACT_BLK_IND;
+
+ mask = YT8512_LED0_DIS_LED_AN_TRY | YT8512_LED0_BT_BLK_EN |
+ YT8512_LED0_HT_BLK_EN | YT8512_LED0_COL_BLK_EN |
+ YT8512_LED0_BT_ON_EN;
+ val &= ~mask;
+
+ ret = ytphy_write_ext(phydev, YT8512_EXTREG_LED0, val);
+ if (ret < 0)
+ return ret;
+
+ val = ytphy_read_ext(phydev, YT8512_EXTREG_LED1);
+ if (val < 0)
+ return val;
+
+ val |= YT8512_LED1_BT_ON_EN;
+
+ mask = YT8512_LED1_TXACT_BLK_EN | YT8512_LED1_RXACT_BLK_EN;
+ val &= ~mask;
+
+ ret = ytphy_write_ext(phydev, YT8512_LED1_BT_ON_EN, val);
+
+ return ret;
+}
+
+static int yt8512_config_init(struct phy_device *phydev)
+{
+ int ret;
+ int val;
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ ret = ytphy_config_init(phydev);
+#else
+ ret = genphy_config_init(phydev);
+#endif
+ if (ret < 0)
+ return ret;
+
+ ret = yt8512_clk_init(phydev);
+ if (ret < 0)
+ return ret;
+
+ ret = yt8512_led_init(phydev);
+
+ /* disable auto sleep */
+ val = ytphy_read_ext(phydev, YT8512_EXTREG_SLEEP_CONTROL1);
+ if (val < 0)
+ return val;
+
+ val &= (~BIT(YT8512_EN_SLEEP_SW_BIT));
+
+ ret = ytphy_write_ext(phydev, YT8512_EXTREG_SLEEP_CONTROL1, val);
+ if (ret < 0)
+ return ret;
+
+ return ret;
+}
+
+static int yt8512_read_status(struct phy_device *phydev)
+{
+ int ret;
+ int val;
+ int speed, speed_mode, duplex;
+
+ ret = genphy_update_link(phydev);
+ if (ret)
+ return ret;
+
+ val = phy_read(phydev, REG_PHY_SPEC_STATUS);
+ if (val < 0)
+ return val;
+
+ duplex = (val & YT8512_DUPLEX) >> YT8512_DUPLEX_BIT;
+ speed_mode = (val & YT8512_SPEED_MODE) >> YT8512_SPEED_MODE_BIT;
+ switch (speed_mode) {
+ case 0:
+ speed = SPEED_10;
+ break;
+ case 1:
+ speed = SPEED_100;
+ break;
+ case 2:
+ case 3:
+ default:
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ speed = -1;
+#else
+ speed = SPEED_UNKNOWN;
+#endif
+ break;
+ }
+
+ phydev->speed = speed;
+ phydev->duplex = duplex;
+
+ return 0;
+}
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+#else
+#if 0
+int yt8521_soft_reset(struct phy_device *phydev)
+{
+ int ret;
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0)
+ return ret;
+
+ ytphy_write_ext(phydev, 0xa000, 2);
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0) {
+ ytphy_write_ext(phydev, 0xa000, 0);
+ return ret;
+ }
+
+ return 0;
+}
+#else
+/* qingsong feedback 2 genphy_soft_reset will cause problem.
+ * and this is the reduction version
+ */
+int yt8521_soft_reset(struct phy_device *phydev)
+{
+ int ret, val;
+
+ val = ytphy_read_ext(phydev, 0xa001);
+ ytphy_write_ext(phydev, 0xa001, (val & ~0x8000));
+
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+#endif
+
+#endif
+
+#if GMAC_CLOCK_INPUT_NEEDED
+static int ytphy_mii_rd_ext(struct mii_bus *bus, int phy_id, u32 regnum)
+{
+ int ret;
+ int val;
+
+ ret = bus->write(bus, phy_id, REG_DEBUG_ADDR_OFFSET, regnum);
+ if (ret < 0)
+ return ret;
+
+ val = bus->read(bus, phy_id, REG_DEBUG_DATA);
+
+ return val;
+}
+
+static int ytphy_mii_wr_ext(struct mii_bus *bus, int phy_id, u32 regnum, u16 val)
+{
+ int ret;
+
+ ret = bus->write(bus, phy_id, REG_DEBUG_ADDR_OFFSET, regnum);
+ if (ret < 0)
+ return ret;
+
+ ret = bus->write(bus, phy_id, REG_DEBUG_DATA, val);
+
+ return ret;
+}
+
+int yt8511_config_dis_txdelay(struct mii_bus *bus, int phy_id)
+{
+ int ret;
+ int val;
+
+ /* disable auto sleep */
+ val = ytphy_mii_rd_ext(bus, phy_id, 0x27);
+ if (val < 0)
+ return val;
+
+ val &= (~BIT(15));
+
+ ret = ytphy_mii_wr_ext(bus, phy_id, 0x27, val);
+ if (ret < 0)
+ return ret;
+
+ /* enable RXC clock when no wire plug */
+ val = ytphy_mii_rd_ext(bus, phy_id, 0xc);
+ if (val < 0)
+ return val;
+
+ /* ext reg 0xc b[7:4]
+ Tx Delay time = 150ps * N - 250ps
+ */
+ val &= ~(0xf << 4);
+ ret = ytphy_mii_wr_ext(bus, phy_id, 0xc, val);
+ //printk("yt8511_config_dis_txdelay..phy txdelay, val=%#08x\n",val);
+
+ return ret;
+}
+
+int phy_yt8531_led_fixup(struct mii_bus *bus, int addr)
+{
+ //printk("%s in\n", __func__);
+
+ ytphy_mii_wr_ext(bus, addr, 0xa00d, 0x670);
+ ytphy_mii_wr_ext(bus, addr, 0xa00e, 0x2070);
+ ytphy_mii_wr_ext(bus, addr, 0xa00f, 0x7e);
+
+ return 0;
+}
+
+int yt8511_config_out_125m(struct mii_bus *bus, int addr)
+{
+ int ret;
+ int val;
+
+ mdelay(100);
+ ret = ytphy_mii_wr_ext(bus, addr, 0xa012, 0xd0);
+
+ mdelay(100);
+ val = ytphy_mii_rd_ext(bus, addr, 0xa012);
+
+ if(val != 0xd0)
+ {
+ printk("yt8511_config_out_125m error\n");
+ return -1;
+ }
+
+ /* disable auto sleep */
+ val = ytphy_mii_rd_ext(bus, addr, 0x27);
+ if (val < 0)
+ return val;
+
+ val &= (~BIT(15));
+
+ ret = ytphy_mii_wr_ext(bus, addr, 0x27, val);
+ if (ret < 0)
+ return ret;
+
+ /* enable RXC clock when no wire plug */
+ val = ytphy_mii_rd_ext(bus, addr, 0xc);
+ if (val < 0)
+ return val;
+
+ /* ext reg 0xc.b[2:1]
+ 00-----25M from pll;
+ 01---- 25M from xtl;(default)
+ 10-----62.5M from pll;
+ 11----125M from pll(here set to this value)
+ */
+ val |= (3 << 1);
+ ret = ytphy_mii_wr_ext(bus, addr, 0xc, val);
+ //printk("yt8511_config_out_125m, phy clk out, val=%#08x\n",val);
+
+#if 0
+ /* for customer, please enable it based on demand.
+ * configure to master
+ */
+ val = bus->read(bus, phy_id, 0x9/*master/slave config reg*/);
+ val |= (0x3<<11); //to be manual config and force to be master
+ ret = bus->write(bus, phy_id, 0x9, val); //take effect until phy soft reset
+ if (ret < 0)
+ return ret;
+
+ printk("yt8511_config_out_125m, phy to be master, val=%#08x\n",val);
+#endif
+
+ return ret;
+}
+
+EXPORT_SYMBOL(yt8511_config_out_125m);
static int yt8511_config_init(struct phy_device *phydev)
{
- int oldpage, ret = 0;
- unsigned int ge, fe;
+ int ret;
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ ret = ytphy_config_init(phydev);
+#else
+ ret = genphy_config_init(phydev);
+#endif
+
+ return ret;
+}
+#endif /*GMAC_CLOCK_INPUT_NEEDED*/
+
+#if (YTPHY_ENABLE_WOL)
+static int ytphy_switch_reg_space(struct phy_device *phydev, int space)
+{
+ int ret;
+
+ if (space == YTPHY_REG_SPACE_UTP){
+ ret = ytphy_write_ext(phydev, 0xa000, 0);
+ }else{
+ ret = ytphy_write_ext(phydev, 0xa000, 2);
+ }
+
+ return ret;
+}
+
+static int ytphy_wol_en_cfg(struct phy_device *phydev, ytphy_wol_cfg_t wol_cfg)
+{
+ int ret=0;
+ int val=0;
+
+ val = ytphy_read_ext(phydev, YTPHY_WOL_CFG_REG);
+ if (val < 0)
+ return val;
+
+ if(wol_cfg.enable) {
+ val |= YTPHY_WOL_CFG_EN;
+
+ if(wol_cfg.type == YTPHY_WOL_TYPE_LEVEL) {
+ val &= ~YTPHY_WOL_CFG_TYPE;
+ val &= ~YTPHY_WOL_CFG_INTR_SEL;
+ } else if(wol_cfg.type == YTPHY_WOL_TYPE_PULSE) {
+ val |= YTPHY_WOL_CFG_TYPE;
+ val |= YTPHY_WOL_CFG_INTR_SEL;
+
+ if(wol_cfg.width == YTPHY_WOL_WIDTH_84MS) {
+ val &= ~YTPHY_WOL_CFG_WIDTH1;
+ val &= ~YTPHY_WOL_CFG_WIDTH2;
+ } else if(wol_cfg.width == YTPHY_WOL_WIDTH_168MS) {
+ val |= YTPHY_WOL_CFG_WIDTH1;
+ val &= ~YTPHY_WOL_CFG_WIDTH2;
+ } else if(wol_cfg.width == YTPHY_WOL_WIDTH_336MS) {
+ val &= ~YTPHY_WOL_CFG_WIDTH1;
+ val |= YTPHY_WOL_CFG_WIDTH2;
+ } else if(wol_cfg.width == YTPHY_WOL_WIDTH_672MS) {
+ val |= YTPHY_WOL_CFG_WIDTH1;
+ val |= YTPHY_WOL_CFG_WIDTH2;
+ }
+ }
+ } else {
+ val &= ~YTPHY_WOL_CFG_EN;
+ val &= ~YTPHY_WOL_CFG_INTR_SEL;
+ }
+
+ ret = ytphy_write_ext(phydev, YTPHY_WOL_CFG_REG, val);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static void ytphy_get_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol)
+{
+ int val = 0;
+
+ wol->supported = WAKE_MAGIC;
+ wol->wolopts = 0;
+
+ val = ytphy_read_ext(phydev, YTPHY_WOL_CFG_REG);
+ if (val < 0)
+ return;
+
+ if (val & YTPHY_WOL_CFG_EN)
+ wol->wolopts |= WAKE_MAGIC;
+
+ return;
+}
+
+static int ytphy_set_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol)
+{
+ int ret, pre_page, val;
+ ytphy_wol_cfg_t wol_cfg;
+ struct net_device *p_attached_dev = phydev->attached_dev;
+
+ memset(&wol_cfg,0,sizeof(ytphy_wol_cfg_t));
+ pre_page = ytphy_read_ext(phydev, 0xa000);
+ if (pre_page < 0)
+ return pre_page;
+
+ /* Switch to phy UTP page */
+ ret = ytphy_switch_reg_space(phydev, YTPHY_REG_SPACE_UTP);
+ if (ret < 0)
+ return ret;
+
+ if (wol->wolopts & WAKE_MAGIC) {
+
+ /* Enable the WOL interrupt */
+ val = phy_read(phydev, YTPHY_UTP_INTR_REG);
+ val |= YTPHY_WOL_INTR;
+ ret = phy_write(phydev, YTPHY_UTP_INTR_REG, val);
+ if (ret < 0)
+ return ret;
+
+ /* Set the WOL config */
+ wol_cfg.enable = 1; //enable
+ wol_cfg.type= YTPHY_WOL_TYPE_PULSE;
+ wol_cfg.width= YTPHY_WOL_WIDTH_672MS;
+ ret = ytphy_wol_en_cfg(phydev, wol_cfg);
+ if (ret < 0)
+ return ret;
+
+ /* Store the device address for the magic packet */
+ ret = ytphy_write_ext(phydev, YTPHY_MAGIC_PACKET_MAC_ADDR2,
+ ((p_attached_dev->dev_addr[0] << 8) |
+ p_attached_dev->dev_addr[1]));
+ if (ret < 0)
+ return ret;
+ ret = ytphy_write_ext(phydev, YTPHY_MAGIC_PACKET_MAC_ADDR1,
+ ((p_attached_dev->dev_addr[2] << 8) |
+ p_attached_dev->dev_addr[3]));
+ if (ret < 0)
+ return ret;
+ ret = ytphy_write_ext(phydev, YTPHY_MAGIC_PACKET_MAC_ADDR0,
+ ((p_attached_dev->dev_addr[4] << 8) |
+ p_attached_dev->dev_addr[5]));
+ if (ret < 0)
+ return ret;
+ } else {
+ wol_cfg.enable = 0; //disable
+ wol_cfg.type= YTPHY_WOL_TYPE_MAX;
+ wol_cfg.width= YTPHY_WOL_WIDTH_MAX;
+ ret = ytphy_wol_en_cfg(phydev, wol_cfg);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* Recover to previous register space page */
+ ret = ytphy_switch_reg_space(phydev, pre_page);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+#endif /*(YTPHY_ENABLE_WOL)*/
+
+static int yt8521_config_init(struct phy_device *phydev)
+{
+ int ret;
+ int val;
+
+ phydev->irq = PHY_POLL;
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ ret = ytphy_config_init(phydev);
+#else
+ ret = genphy_config_init(phydev);
+#endif
+ if (ret < 0)
+ return ret;
+
+ /* disable auto sleep */
+ val = ytphy_read_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1);
+ if (val < 0)
+ return val;
+
+ val &= (~BIT(YT8521_EN_SLEEP_SW_BIT));
+
+ ret = ytphy_write_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1, val);
+ if (ret < 0)
+ return ret;
- oldpage = phy_select_page(phydev, YT8511_EXT_CLK_GATE);
- if (oldpage < 0)
- goto err_restore_page;
+ /* enable RXC clock when no wire plug */
+ ret = ytphy_write_ext(phydev, 0xa000, 0);
+ if (ret < 0)
+ return ret;
+
+ val = ytphy_read_ext(phydev, 0xc);
+ if (val < 0)
+ return val;
+ val &= ~(1 << 12);
+ ret = ytphy_write_ext(phydev, 0xc, val);
+ if (ret < 0)
+ return ret;
- /* set rgmii delay mode */
- switch (phydev->interface) {
- case PHY_INTERFACE_MODE_RGMII:
- ge = YT8511_DELAY_GE_TX_DIS;
- fe = YT8511_DELAY_FE_TX_DIS;
+ printk (KERN_INFO "yt8521_config_init, 8521 init call out.\n");
+ return ret;
+}
+
+/*
+ * for fiber mode, there is no 10M speed mode and
+ * this function is for this purpose.
+ */
+static int yt8521_adjust_status(struct phy_device *phydev, int val, int is_utp)
+{
+ int speed_mode, duplex;
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ int speed = -1;
+#else
+ int speed = SPEED_UNKNOWN;
+#endif
+
+ duplex = (val & YT8512_DUPLEX) >> YT8521_DUPLEX_BIT;
+ speed_mode = (val & YT8521_SPEED_MODE) >> YT8521_SPEED_MODE_BIT;
+ switch (speed_mode) {
+ case 0:
+ if (is_utp)
+ speed = SPEED_10;
+ break;
+ case 1:
+ speed = SPEED_100;
break;
- case PHY_INTERFACE_MODE_RGMII_RXID:
- ge = YT8511_DELAY_RX | YT8511_DELAY_GE_TX_DIS;
- fe = YT8511_DELAY_FE_TX_DIS;
+ case 2:
+ speed = SPEED_1000;
break;
- case PHY_INTERFACE_MODE_RGMII_TXID:
- ge = YT8511_DELAY_GE_TX_EN;
- fe = YT8511_DELAY_FE_TX_EN;
+ case 3:
break;
- case PHY_INTERFACE_MODE_RGMII_ID:
- ge = YT8511_DELAY_RX | YT8511_DELAY_GE_TX_EN;
- fe = YT8511_DELAY_FE_TX_EN;
+ default:
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ speed = -1;
+#else
+ speed = SPEED_UNKNOWN;
+#endif
break;
- default: /* do not support other modes */
- ret = -EOPNOTSUPP;
- goto err_restore_page;
}
- ret = __phy_modify(phydev, YT8511_PAGE, (YT8511_DELAY_RX | YT8511_DELAY_GE_TX_EN), ge);
+ phydev->speed = speed;
+ phydev->duplex = duplex;
+ //printk (KERN_INFO "yt8521_adjust_status call out,regval=0x%04x,mode=%s,speed=%dm...\n", val,is_utp?"utp":"fiber", phydev->speed);
+
+ return 0;
+}
+
+/*
+ * for fiber mode, when speed is 100M, there is no definition for autonegotiation, and
+ * this function handles this case and return 1 per linux kernel's polling.
+ */
+int yt8521_aneg_done (struct phy_device *phydev)
+{
+
+ //printk("yt8521_aneg_done callin,speed=%dm,linkmoded=%d\n", phydev->speed,link_mode_8521);
+
+ if((32 == link_mode_8521) && (SPEED_100 == phydev->speed))
+ {
+ return 1/*link_mode_8521*/;
+ }
+
+#if ( LINUX_VERSION_CODE > KERNEL_VERSION(3,11,0) )
+ return genphy_aneg_done(phydev);
+#else
+ return 1;
+#endif
+}
+
+static int yt8521_read_status(struct phy_device *phydev)
+{
+ int ret;
+ volatile int val, yt8521_fiber_latch_val, yt8521_fiber_curr_val;
+ volatile int link;
+ int link_utp = 0, link_fiber = 0;
+
+#if (YT8521_PHY_MODE_CURR != YT8521_PHY_MODE_FIBER)
+ /* reading UTP */
+ ret = ytphy_write_ext(phydev, 0xa000, 0);
+ if (ret < 0)
+ return ret;
+
+ val = phy_read(phydev, REG_PHY_SPEC_STATUS);
+ if (val < 0)
+ return val;
+
+ link = val & (BIT(YT8521_LINK_STATUS_BIT));
+ if (link) {
+ link_utp = 1;
+ link_mode_8521 = 1;
+ yt8521_adjust_status(phydev, val, 1);
+ } else {
+ link_utp = 0;
+ }
+#endif //(YT8521_PHY_MODE_CURR != YT8521_PHY_MODE_FIBER)
+
+#if (YT8521_PHY_MODE_CURR != YT8521_PHY_MODE_UTP)
+ /* reading Fiber */
+ ret = ytphy_write_ext(phydev, 0xa000, 2);
+ if (ret < 0)
+ return ret;
+
+ val = phy_read(phydev, REG_PHY_SPEC_STATUS);
+ if (val < 0)
+ return val;
+
+ //note: below debug information is used to check multiple PHy ports.
+ //printk (KERN_INFO "yt8521_read_status, fiber status=%04x,macbase=0x%08lx\n", val,(unsigned long)phydev->attached_dev);
+
+ /* for fiber, from 1000m to 100m, there is not link down from 0x11, and check reg 1 to identify such case
+ * this is important for Linux kernel for that, missing linkdown event will cause problem.
+ */
+ yt8521_fiber_latch_val = phy_read(phydev, MII_BMSR);
+ yt8521_fiber_curr_val = phy_read(phydev, MII_BMSR);
+ link = val & (BIT(YT8521_LINK_STATUS_BIT));
+ if((link) && (yt8521_fiber_latch_val != yt8521_fiber_curr_val))
+ {
+ link = 0;
+ printk (KERN_INFO "yt8521_read_status, fiber link down detect,latch=%04x,curr=%04x\n", yt8521_fiber_latch_val,yt8521_fiber_curr_val);
+ }
+
+ if (link) {
+ link_fiber = 1;
+ yt8521_adjust_status(phydev, val, 0);
+ link_mode_8521 = 32; //fiber mode
+
+
+ } else {
+ link_fiber = 0;
+ }
+#endif //(YT8521_PHY_MODE_CURR != YT8521_PHY_MODE_UTP)
+
+ if (link_utp || link_fiber) {
+ phydev->link = 1;
+ } else {
+ phydev->link = 0;
+ link_mode_8521 = 0;
+ }
+
+#if (YT8521_PHY_MODE_CURR != YT8521_PHY_MODE_FIBER)
+ if (link_utp) {
+ ytphy_write_ext(phydev, 0xa000, 0);
+ }
+#endif
+
+ //printk (KERN_INFO "yzhang..8521 read status call out,link=%d,linkmode=%d\n", phydev->link, link_mode_8521 );
+ return 0;
+}
+
+int yt8521_suspend(struct phy_device *phydev)
+{
+#if !(SYS_WAKEUP_BASED_ON_ETH_PKT)
+ int value;
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_lock(&phydev->lock);
+#else
+ /* no need lock in 4.19 */
+#endif
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value | BMCR_PDOWN);
+
+ ytphy_write_ext(phydev, 0xa000, 2);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value | BMCR_PDOWN);
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_unlock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+#endif /*!(SYS_WAKEUP_BASED_ON_ETH_PKT)*/
+
+ return 0;
+}
+
+int yt8521_resume(struct phy_device *phydev)
+{
+#if !(SYS_WAKEUP_BASED_ON_ETH_PKT)
+ int value;
+ int ret;
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_lock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value & ~BMCR_PDOWN);
+
+ /* disable auto sleep */
+ value = ytphy_read_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1);
+ if (value < 0)
+ return value;
+
+ value &= (~BIT(YT8521_EN_SLEEP_SW_BIT));
+ ret = ytphy_write_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1, value);
if (ret < 0)
- goto err_restore_page;
+ return ret;
+
+ /* enable RXC clock when no wire plug */
+ value = ytphy_read_ext(phydev, 0xc);
+ if (value < 0)
+ return value;
+ value &= ~(1 << 12);
+ ret = ytphy_write_ext(phydev, 0xc, value);
+ if (ret < 0)
+ return ret;
+
+ ytphy_write_ext(phydev, 0xa000, 2);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value & ~BMCR_PDOWN);
+
+#if (YT8521_PHY_MODE_CURR != YT8521_PHY_MODE_FIBER)
+ ytphy_write_ext(phydev, 0xa000, 0);
+#endif
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_unlock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+#endif /*!(SYS_WAKEUP_BASED_ON_ETH_PKT)*/
+
+ return 0;
+}
+
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+#else
+int yt8618_soft_reset(struct phy_device *phydev)
+{
+ int ret;
- /* set clock mode to 125mhz */
- ret = __phy_modify(phydev, YT8511_PAGE, 0, YT8511_CLK_125M);
+ ytphy_write_ext(phydev, 0xa000, 0);
+ ret = genphy_soft_reset(phydev);
if (ret < 0)
- goto err_restore_page;
+ return ret;
- /* fast ethernet delay is in a separate page */
- ret = __phy_write(phydev, YT8511_PAGE_SELECT, YT8511_EXT_DELAY_DRIVE);
+ return 0;
+}
+
+int yt8614_soft_reset(struct phy_device *phydev)
+{
+ int ret;
+
+ /* utp */
+ ytphy_write_ext(phydev, 0xa000, 0);
+ ret = genphy_soft_reset(phydev);
if (ret < 0)
- goto err_restore_page;
+ return ret;
+
+ /* qsgmii */
+ ytphy_write_ext(phydev, 0xa000, 2);
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0) {
+ ytphy_write_ext(phydev, 0xa000, 0); //back to utp mode
+ return ret;
+ }
+
+ /* sgmii */
+ ytphy_write_ext(phydev, 0xa000, 3);
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0) {
+ ytphy_write_ext(phydev, 0xa000, 0); //back to utp mode
+ return ret;
+ }
+
+ return 0;
+}
+
+#endif
+
+static int yt8618_config_init(struct phy_device *phydev)
+{
+ int ret;
+ int val;
+
+ phydev->irq = PHY_POLL;
+
+ if(0xff == yt_mport_base_phy_addr)
+ /* by default, we think the first phy should be the base phy addr. for mul */
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ {
+ yt_mport_base_phy_addr = phydev->addr;
+ }else if (yt_mport_base_phy_addr > phydev->addr) {
+ printk (KERN_INFO "yzhang..8618 init, phy address mismatch, base=%d, cur=%d\n", yt_mport_base_phy_addr, phydev->addr);
+ }
+#else
+ {
+ yt_mport_base_phy_addr = phydev->mdio.addr;
+ }else if (yt_mport_base_phy_addr > phydev->mdio.addr) {
+ printk (KERN_INFO "yzhang..8618 init, phy address mismatch, base=%d, cur=%d\n", yt_mport_base_phy_addr, phydev->mdio.addr);
+ }
+#endif
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ ret = ytphy_config_init(phydev);
+#else
+ ret = genphy_config_init(phydev);
+#endif
+ if (ret < 0)
+ return ret;
+
+ /* for utp to optimize signal */
+ ret = ytphy_write_ext(phydev, 0x41, 0x33);
+ if (ret < 0)
+ return ret;
+ ret = ytphy_write_ext(phydev, 0x42, 0x66);
+ if (ret < 0)
+ return ret;
+ ret = ytphy_write_ext(phydev, 0x43, 0xaa);
+ if (ret < 0)
+ return ret;
+ ret = ytphy_write_ext(phydev, 0x44, 0xd0d);
+ if (ret < 0)
+ return ret;
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ if((phydev->addr > yt_mport_base_phy_addr) && ((2 == phydev->addr - yt_mport_base_phy_addr) || (5 == phydev->addr - yt_mport_base_phy_addr)))
+#else
+ if((phydev->mdio.addr > yt_mport_base_phy_addr) && ((2 == phydev->mdio.addr - yt_mport_base_phy_addr) || (5 == phydev->mdio.addr - yt_mport_base_phy_addr)))
+#endif
+ {
+ ret = ytphy_write_ext(phydev, 0x44, 0x2929);
+ if (ret < 0)
+ return ret;
+ }
+
+ val = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, val | BMCR_RESET);
+
+ printk (KERN_INFO "yt8618_config_init call out.\n");
+ return ret;
+}
+
+static int yt8614_config_init(struct phy_device *phydev)
+{
+ int ret = 0;
+
+ phydev->irq = PHY_POLL;
- ret = __phy_modify(phydev, YT8511_PAGE, YT8511_DELAY_FE_TX_EN, fe);
+ if(0xff == yt_mport_base_phy_addr_8614)
+ /* by default, we think the first phy should be the base phy addr. for mul */
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ {
+ yt_mport_base_phy_addr_8614 = (unsigned int)phydev->addr;
+ }else if (yt_mport_base_phy_addr_8614 > (unsigned int)phydev->addr) {
+ printk (KERN_INFO "yzhang..8618 init, phy address mismatch, base=%u, cur=%d\n", yt_mport_base_phy_addr_8614, phydev->addr);
+ }
+#else
+ {
+ yt_mport_base_phy_addr_8614 = (unsigned int)phydev->mdio.addr;
+ }else if (yt_mport_base_phy_addr_8614 > (unsigned int)phydev->mdio.addr) {
+ printk (KERN_INFO "yzhang..8618 init, phy address mismatch, base=%u, cur=%d\n", yt_mport_base_phy_addr_8614, phydev->mdio.addr);
+ }
+#endif
+ return ret;
+}
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+#define yt8614_get_port_from_phydev(phydev) ((0xff == yt_mport_base_phy_addr_8614) && (yt_mport_base_phy_addr_8614 <= (phydev)->addr) ? 0 : (unsigned int)((phydev)->addr) - yt_mport_base_phy_addr_8614)
+#else
+#define yt8614_get_port_from_phydev(phydev) ((0xff == yt_mport_base_phy_addr_8614) && (yt_mport_base_phy_addr_8614 <= (phydev)->mdio.addr) ? 0 : (unsigned int)((phydev)->mdio.addr) - yt_mport_base_phy_addr_8614)
+#endif
+
+int yt8618_aneg_done (struct phy_device *phydev)
+{
+
+ return genphy_aneg_done(phydev);
+}
+
+int yt8614_aneg_done (struct phy_device *phydev)
+{
+ int port = yt8614_get_port_from_phydev(phydev);
+
+ /*it should be used for 8614 fiber*/
+ if((32 == link_mode_8614[port]) && (SPEED_100 == phydev->speed))
+ {
+ return 1;
+ }
+
+ return genphy_aneg_done(phydev);
+}
+
+static int yt8614_read_status(struct phy_device *phydev)
+{
+ //int i;
+ int ret;
+ volatile int val, yt8614_fiber_latch_val, yt8614_fiber_curr_val;
+ volatile int link;
+ int link_utp = 0, link_fiber = 0;
+ int port = yt8614_get_port_from_phydev(phydev);
+
+#if (YT8614_PHY_MODE_CURR != YT8521_PHY_MODE_FIBER)
+ /* switch to utp and reading regs */
+ ret = ytphy_write_ext(phydev, 0xa000, 0);
if (ret < 0)
- goto err_restore_page;
+ return ret;
+
+ val = phy_read(phydev, REG_PHY_SPEC_STATUS);
+ if (val < 0)
+ return val;
- /* leave pll enabled in sleep */
- ret = __phy_write(phydev, YT8511_PAGE_SELECT, YT8511_EXT_SLEEP_CTRL);
+ link = val & (BIT(YT8521_LINK_STATUS_BIT));
+ if (link) {
+ link_utp = 1;
+ // here is same as 8521 and re-use the function;
+ yt8521_adjust_status(phydev, val, 1);
+ } else {
+ link_utp = 0;
+ }
+#endif //(YT8614_PHY_MODE_CURR != YT8521_PHY_MODE_FIBER)
+
+#if (YT8614_PHY_MODE_CURR != YT8521_PHY_MODE_UTP)
+ /* reading Fiber/sgmii */
+ ret = ytphy_write_ext(phydev, 0xa000, 3);
if (ret < 0)
- goto err_restore_page;
+ return ret;
+
+ val = phy_read(phydev, REG_PHY_SPEC_STATUS);
+ if (val < 0)
+ return val;
+
+ //printk (KERN_INFO "yzhang..8614 read fiber status=%04x,macbase=0x%08lx\n", val,(unsigned long)phydev->attached_dev);
+
+ /* for fiber, from 1000m to 100m, there is not link down from 0x11, and check reg 1 to identify such case */
+ yt8614_fiber_latch_val = phy_read(phydev, MII_BMSR);
+ yt8614_fiber_curr_val = phy_read(phydev, MII_BMSR);
+ link = val & (BIT(YT8521_LINK_STATUS_BIT));
+ if((link) && (yt8614_fiber_latch_val != yt8614_fiber_curr_val))
+ {
+ link = 0;
+ printk (KERN_INFO "yt8614_read_status, fiber link down detect,latch=%04x,curr=%04x\n", yt8614_fiber_latch_val,yt8614_fiber_curr_val);
+ }
+
+ if (link) {
+ link_fiber = 1;
+ yt8521_adjust_status(phydev, val, 0);
+ link_mode_8614[port] = 32; //fiber mode
- ret = __phy_modify(phydev, YT8511_PAGE, 0, YT8511_PLLON_SLP);
+
+ } else {
+ link_fiber = 0;
+ }
+#endif //(YT8521_PHY_MODE_CURR != YT8521_PHY_MODE_UTP)
+
+ if (link_utp || link_fiber) {
+ phydev->link = 1;
+ } else {
+ phydev->link = 0;
+ link_mode_8614[port] = 0;
+ }
+
+#if (YT8614_PHY_MODE_CURR != YT8521_PHY_MODE_FIBER)
+ if (link_utp) {
+ ytphy_write_ext(phydev, 0xa000, 0);
+ }
+#endif
+ //printk (KERN_INFO "yt8614_read_status call out,link=%d,linkmode=%d\n", phydev->link, link_mode_8614[port] );
+
+ return 0;
+}
+
+static int yt8618_read_status(struct phy_device *phydev)
+{
+ int ret;
+ volatile int val; //maybe for 8614 yt8521_fiber_latch_val, yt8521_fiber_curr_val;
+ volatile int link;
+ int link_utp = 0, link_fiber = 0;
+
+ /* switch to utp and reading regs */
+ ret = ytphy_write_ext(phydev, 0xa000, 0);
if (ret < 0)
- goto err_restore_page;
+ return ret;
+
+ val = phy_read(phydev, REG_PHY_SPEC_STATUS);
+ if (val < 0)
+ return val;
+
+ link = val & (BIT(YT8521_LINK_STATUS_BIT));
+ if (link) {
+ link_utp = 1;
+ yt8521_adjust_status(phydev, val, 1);
+ } else {
+ link_utp = 0;
+ }
+
+ if (link_utp || link_fiber) {
+ phydev->link = 1;
+ } else {
+ phydev->link = 0;
+ }
+
+ return 0;
+}
+
+int yt8618_suspend(struct phy_device *phydev)
+{
+#if !(SYS_WAKEUP_BASED_ON_ETH_PKT)
+ int value;
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_lock(&phydev->lock);
+#else
+ /* no need lock in 4.19 */
+#endif
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value | BMCR_PDOWN);
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_unlock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+#endif /*!(SYS_WAKEUP_BASED_ON_ETH_PKT)*/
+
+ return 0;
+}
-err_restore_page:
- return phy_restore_page(phydev, oldpage, ret);
+int yt8618_resume(struct phy_device *phydev)
+{
+#if !(SYS_WAKEUP_BASED_ON_ETH_PKT)
+ int value;
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_lock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value & ~BMCR_PDOWN);
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_unlock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+#endif /*!(SYS_WAKEUP_BASED_ON_ETH_PKT)*/
+
+ return 0;
+}
+
+int yt8614_suspend(struct phy_device *phydev)
+{
+#if !(SYS_WAKEUP_BASED_ON_ETH_PKT)
+ int value;
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_lock(&phydev->lock);
+#else
+ /* no need lock in 4.19 */
+#endif
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value | BMCR_PDOWN);
+
+ ytphy_write_ext(phydev, 0xa000, 3);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value | BMCR_PDOWN);
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_unlock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+#endif /*!(SYS_WAKEUP_BASED_ON_ETH_PKT)*/
+
+ return 0;
}
-static struct phy_driver motorcomm_phy_drvs[] = {
+int yt8614_resume(struct phy_device *phydev)
+{
+#if !(SYS_WAKEUP_BASED_ON_ETH_PKT)
+ int value;
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_lock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value & ~BMCR_PDOWN);
+
+ ytphy_write_ext(phydev, 0xa000, 3);
+ value = phy_read(phydev, MII_BMCR);
+ phy_write(phydev, MII_BMCR, value & ~BMCR_PDOWN);
+
+ ytphy_write_ext(phydev, 0xa000, 0);
+
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ mutex_unlock(&phydev->lock);
+#else
+ /* no need lock/unlock in 4.19 */
+#endif
+#endif /*!(SYS_WAKEUP_BASED_ON_ETH_PKT)*/
+
+ return 0;
+}
+
+
+static struct phy_driver ytphy_drvs[] = {
{
- PHY_ID_MATCH_EXACT(PHY_ID_YT8511),
+ .phy_id = PHY_ID_YT8010,
+ .name = "YT8010 Automotive Ethernet",
+ .phy_id_mask = MOTORCOMM_PHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+#endif
+ .config_aneg = yt8010_config_aneg,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ .config_init = ytphy_config_init,
+#else
+ .config_init = genphy_config_init,
+#endif
+ .read_status = genphy_read_status,
+ }, {
+ .phy_id = PHY_ID_YT8510,
+ .name = "YT8510 100/10Mb Ethernet",
+ .phy_id_mask = MOTORCOMM_PHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+#endif
+ .config_aneg = genphy_config_aneg,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ .config_init = ytphy_config_init,
+#else
+ .config_init = genphy_config_init,
+#endif
+ .read_status = genphy_read_status,
+ }, {
+ .phy_id = PHY_ID_YT8511,
.name = "YT8511 Gigabit Ethernet",
+ .phy_id_mask = MOTORCOMM_PHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+#endif
+ .config_aneg = genphy_config_aneg,
+#if GMAC_CLOCK_INPUT_NEEDED
.config_init = yt8511_config_init,
+#else
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ .config_init = ytphy_config_init,
+#else
+ .config_init = genphy_config_init,
+#endif
+#endif
+ .read_status = genphy_read_status,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ }, {
+ .phy_id = PHY_ID_YT8512,
+ .name = "YT8512 Ethernet",
+ .phy_id_mask = MOTORCOMM_PHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+#endif
+ .config_aneg = genphy_config_aneg,
+ .config_init = yt8512_config_init,
+ .read_status = yt8512_read_status,
.suspend = genphy_suspend,
.resume = genphy_resume,
- .read_page = yt8511_read_page,
- .write_page = yt8511_write_page,
- },
+ }, {
+ .phy_id = PHY_ID_YT8512B,
+ .name = "YT8512B Ethernet",
+ .phy_id_mask = MOTORCOMM_PHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+#endif
+ .config_aneg = genphy_config_aneg,
+ .config_init = yt8512_config_init,
+ .read_status = yt8512_read_status,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ }, {
+ .phy_id = PHY_ID_YT8521,
+ .name = "YT8521 Ethernet",
+ .phy_id_mask = MOTORCOMM_PHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES | PHY_GBIT_FEATURES,
+#endif
+ .flags = PHY_POLL,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+#else
+ .soft_reset = yt8521_soft_reset,
+#endif
+ .config_aneg = genphy_config_aneg,
+#if ( LINUX_VERSION_CODE > KERNEL_VERSION(3,11,0) )
+ .aneg_done = yt8521_aneg_done,
+#endif
+ .config_init = yt8521_config_init,
+ .read_status = yt8521_read_status,
+ .suspend = yt8521_suspend,
+ .resume = yt8521_resume,
+#if (YTPHY_ENABLE_WOL)
+ .get_wol = &ytphy_get_wol,
+ .set_wol = &ytphy_set_wol,
+#endif
+ },{
+ /* same as 8521 */
+ .phy_id = PHY_ID_YT8531S,
+ .name = "YT8531S Ethernet",
+ .phy_id_mask = MOTORCOMM_PHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES | PHY_GBIT_FEATURES,
+#endif
+ .flags = PHY_POLL,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+#else
+ .soft_reset = yt8521_soft_reset,
+#endif
+ .config_aneg = genphy_config_aneg,
+#if ( LINUX_VERSION_CODE > KERNEL_VERSION(3,11,0) )
+ .aneg_done = yt8521_aneg_done,
+#endif
+ .config_init = yt8521_config_init,
+ .read_status = yt8521_read_status,
+ .suspend = yt8521_suspend,
+ .resume = yt8521_resume,
+#if (YTPHY_ENABLE_WOL)
+ .get_wol = &ytphy_get_wol,
+ .set_wol = &ytphy_set_wol,
+#endif
+ }, {
+ /* same as 8511 */
+ .phy_id = PHY_ID_YT8531,
+ .name = "YT8531 Gigabit Ethernet",
+ .phy_id_mask = MOTORCOMM_PHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES | PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+#endif
+ .config_aneg = genphy_config_aneg,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+ .config_init = ytphy_config_init,
+#else
+ .config_init = genphy_config_init,
+#endif
+ .read_status = genphy_read_status,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+#if (YTPHY_ENABLE_WOL)
+ .get_wol = &ytphy_get_wol,
+ .set_wol = &ytphy_set_wol,
+#endif
+ }, {
+ .phy_id = PHY_ID_YT8618,
+ .name = "YT8618 Ethernet",
+ .phy_id_mask = MOTORCOMM_MPHY_ID_MASK,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES | PHY_GBIT_FEATURES,
+#endif
+ .flags = PHY_POLL,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+#else
+ .soft_reset = yt8618_soft_reset,
+#endif
+ .config_aneg = genphy_config_aneg,
+#if ( LINUX_VERSION_CODE > KERNEL_VERSION(3,11,0) )
+ .aneg_done = yt8618_aneg_done,
+#endif
+ .config_init = yt8618_config_init,
+ .read_status = yt8618_read_status,
+ .suspend = yt8618_suspend,
+ .resume = yt8618_resume,
+ }, {
+ .phy_id = PHY_ID_YT8614,
+ .name = "YT8614 Ethernet",
+ .phy_id_mask = MOTORCOMM_MPHY_ID_MASK_8614,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(5,4,0) )
+ .features = PHY_BASIC_FEATURES | PHY_GBIT_FEATURES,
+#endif
+ .flags = PHY_POLL,
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+#else
+ .soft_reset = yt8614_soft_reset,
+#endif
+ .config_aneg = genphy_config_aneg,
+#if ( LINUX_VERSION_CODE > KERNEL_VERSION(3,11,0) )
+ .aneg_done = yt8614_aneg_done,
+#endif
+ .config_init = yt8614_config_init,
+ .read_status = yt8614_read_status,
+ .suspend = yt8614_suspend,
+ .resume = yt8614_resume,
+ },
};
-module_phy_driver(motorcomm_phy_drvs);
+#if ( LINUX_VERSION_CODE < KERNEL_VERSION(4,0,0) )
+static int ytphy_drivers_register(struct phy_driver* phy_drvs, int size)
+{
+ int i, j;
+ int ret;
+
+ for (i = 0; i < size; i++) {
+ ret = phy_driver_register(&phy_drvs[i]);
+ if (ret)
+ goto err;
+ }
+
+ return 0;
+
+err:
+ for (j = 0; j < i; j++)
+ phy_driver_unregister(&phy_drvs[j]);
+
+ return ret;
+}
+
+static void ytphy_drivers_unregister(struct phy_driver* phy_drvs, int size)
+{
+ int i;
+
+ for (i = 0; i < size; i++) {
+ phy_driver_unregister(&phy_drvs[i]);
+ }
+}
+
+static int __init ytphy_init(void)
+{
+ printk("motorcomm phy register\n");
+ return ytphy_drivers_register(ytphy_drvs, ARRAY_SIZE(ytphy_drvs));
+}
+
+static void __exit ytphy_exit(void)
+{
+ printk("motorcomm phy unregister\n");
+ ytphy_drivers_unregister(ytphy_drvs, ARRAY_SIZE(ytphy_drvs));
+}
+
+module_init(ytphy_init);
+module_exit(ytphy_exit);
+#else
+/* for linux 4.x */
+module_phy_driver(ytphy_drvs);
+#endif
MODULE_DESCRIPTION("Motorcomm PHY driver");
-MODULE_AUTHOR("Peter Geis");
+MODULE_AUTHOR("Leilei Zhao");
MODULE_LICENSE("GPL");
-static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = {
- { PHY_ID_MATCH_EXACT(PHY_ID_YT8511) },
- { /* sentinal */ }
+static struct mdio_device_id __maybe_unused motorcomm_tbl[] = {
+ { PHY_ID_YT8010, MOTORCOMM_PHY_ID_MASK },
+ { PHY_ID_YT8510, MOTORCOMM_PHY_ID_MASK },
+ { PHY_ID_YT8511, MOTORCOMM_PHY_ID_MASK },
+ { PHY_ID_YT8512, MOTORCOMM_PHY_ID_MASK },
+ { PHY_ID_YT8512B, MOTORCOMM_PHY_ID_MASK },
+ { PHY_ID_YT8521, MOTORCOMM_PHY_ID_MASK },
+ { PHY_ID_YT8531S, MOTORCOMM_PHY_ID_8531_MASK },
+ { PHY_ID_YT8531, MOTORCOMM_PHY_ID_8531_MASK },
+ { PHY_ID_YT8618, MOTORCOMM_MPHY_ID_MASK },
+ { PHY_ID_YT8614, MOTORCOMM_MPHY_ID_MASK_8614 },
+ { }
};
MODULE_DEVICE_TABLE(mdio, motorcomm_tbl);
+
+
diff --git a/drivers/net/phy/yt8614-phy.h b/drivers/net/phy/yt8614-phy.h
new file mode 100644
index 000000000..56a398338
--- /dev/null
+++ b/drivers/net/phy/yt8614-phy.h
@@ -0,0 +1,491 @@
+#ifndef _PHY_H_
+#define _PHY_H_
+
+
+/* configuration for driver */
+
+#define YT8614_MAX_LPORT_ID 3
+
+#define YT8614_PHY_MODE_FIBER 1 //fiber mode only
+#define YT8614_PHY_MODE_UTP 2 //utp mode only
+#define YT8614_PHY_MODE_POLL 3 //fiber and utp, poll mode
+
+/* please make choice according to system design
+ * for Fiber only system, please define YT8614_PHY_MODE_CURR 1
+ * for UTP only system, please define YT8614_PHY_MODE_CURR 2
+ * for combo system, please define YT8614_PHY_MODE_CURR 3
+ */
+#define YT8614_PHY_MODE_CURR 3
+
+
+
+/* pls dont modify below lines */
+
+#define PHY_ID_YT8614 0x4F51E899 //serdes
+#define MOTORCOMM_MPHY_ID_MASK_8614 0xffffffff
+
+#ifndef BOOL
+#define BOOL unsigned int
+#endif
+
+#ifndef FALSE
+#define FALSE 0
+#endif
+
+#ifndef TRUE
+#define TRUE 1
+#endif
+
+#ifndef SPEED_1000M
+#define SPEED_1000M 2
+#endif
+#ifndef SPEED_100M
+#define SPEED_100M 1
+#endif
+#ifndef SPEED_10M
+#define SPEED_10M 0
+#endif
+
+#ifndef SPEED_UNKNOWN
+#define SPEED_UNKNOWN 0xffff
+#endif
+
+#ifndef DUPLEX_FULL
+#define DUPLEX_FULL 1
+#endif
+#ifndef DUPLEX_HALF
+#define DUPLEX_HALF 0
+#endif
+
+#ifndef BIT
+#define BIT(n) (0x1<<(n))
+#endif
+#ifndef s32
+typedef int s32;
+typedef unsigned int u32;
+typedef unsigned short u16;
+typedef unsigned char u8;
+#endif
+
+#ifndef REG_PHY_SPEC_STATUS
+#define REG_PHY_SPEC_STATUS 0x11
+#define REG_DEBUG_ADDR_OFFSET 0x1e
+#define REG_DEBUG_DATA 0x1f
+#endif
+
+/**********YT8614************************************************/
+
+#define YT8614_SMI_SEL_PHY 0x0
+#define YT8614_SMI_SEL_SDS_QSGMII 0x02
+#define YT8614_SMI_SEL_SDS_SGMII 0x03
+
+/* yt8614 register type */
+#define YT8614_TYPE_COMMON 0x01
+#define YT8614_TYPE_UTP_MII 0x02
+#define YT8614_TYPE_UTP_EXT 0x03
+#define YT8614_TYPE_LDS_MII 0x04
+#define YT8614_TYPE_UTP_MMD 0x05
+#define YT8614_TYPE_SDS_QSGMII_MII 0x06
+#define YT8614_TYPE_SDS_SGMII_MII 0x07
+#define YT8614_TYPE_SDS_QSGMII_EXT 0x08
+#define YT8614_TYPE_SDS_SGMII_EXT 0x09
+
+/* YT8614 extended common register */
+#define YT8614_REG_COM_SMI_MUX 0xA000
+#define YT8614_REG_COM_SLED_CFG0 0xA001
+#define YT8614_REG_COM_PHY_ID 0xA002
+#define YT8614_REG_COM_CHIP_VER 0xA003
+#define YT8614_REG_COM_SLED_CFG 0xA004
+#define YT8614_REG_COM_MODE_CHG_RESET 0xA005
+#define YT8614_REG_COM_SYNCE0_CFG 0xA006
+#define YT8614_REG_COM_CHIP_MODE 0xA007
+
+#define YT8614_REG_COM_HIDE_SPEED 0xA009
+
+#define YT8614_REG_COM_SYNCE1_CFG 0xA00E
+
+#define YT8614_REG_COM_HIDE_FIBER_MODE 0xA019
+
+
+#define YT8614_REG_COM_HIDE_SEL1 0xA054
+#define YT8614_REG_COM_HIDE_LED_CFG2 0xB8
+#define YT8614_REG_COM_HIDE_LED_CFG3 0xB9
+#define YT8614_REG_COM_HIDE_LED_CFG5 0xBB
+
+#define YT8614_REG_COM_HIDE_LED_CFG4 0xBA //not used currently
+
+#if 0
+#define YT8614_REG_COM_HIDE_LED12_CFG 0xA060 //not used currently
+#define YT8614_REG_COM_HIDE_LED13_CFG 0xA061
+#define YT8614_REG_COM_HIDE_LED14_CFG 0xA062
+#define YT8614_REG_COM_HIDE_LED15_CFG 0xA063
+#define YT8614_REG_COM_HIDE_LED16_CFG 0xA064
+#define YT8614_REG_COM_HIDE_LED17_CFG 0xA065
+#define YT8614_REG_COM_HIDE_LED18_CFG 0xA066
+#define YT8614_REG_COM_HIDE_LED19_CFG 0xA067
+#define YT8614_REG_COM_HIDE_LED20_CFG 0xA068
+#define YT8614_REG_COM_HIDE_LED21_CFG 0xA069
+#define YT8614_REG_COM_HIDE_LED22_CFG 0xA06A
+#define YT8614_REG_COM_HIDE_LED23_CFG 0xA06B
+#define YT8614_REG_COM_HIDE_LED24_CFG 0xA06C
+#define YT8614_REG_COM_HIDE_LED25_CFG 0xA06D
+#define YT8614_REG_COM_HIDE_LED26_CFG 0xA06E
+#define YT8614_REG_COM_HIDE_LED27_CFG 0xA06F
+#endif
+
+#define YT8614_REG_COM_HIDE_LED28_CFG 0xA070
+#define YT8614_REG_COM_HIDE_LED29_CFG 0xA071
+#define YT8614_REG_COM_HIDE_LED30_CFG 0xA072
+#define YT8614_REG_COM_HIDE_LED31_CFG 0xA073
+#define YT8614_REG_COM_HIDE_LED32_CFG 0xA074
+#define YT8614_REG_COM_HIDE_LED33_CFG 0xA075
+#define YT8614_REG_COM_HIDE_LED34_CFG 0xA076
+#define YT8614_REG_COM_HIDE_LED35_CFG 0xA077
+
+#define YT8614_REG_COM_PKG_CFG0 0xA0A0
+#define YT8614_REG_COM_PKG_CFG1 0xA0A1
+#define YT8614_REG_COM_PKG_CFG2 0xA0A2
+#define YT8614_REG_COM_PKG_RX_VALID0 0xA0A3
+#define YT8614_REG_COM_PKG_RX_VALID1 0xA0A4
+#define YT8614_REG_COM_PKG_RX_OS0 0xA0A5
+#define YT8614_REG_COM_PKG_RX_OS1 0xA0A6
+#define YT8614_REG_COM_PKG_RX_US0 0xA0A7
+#define YT8614_REG_COM_PKG_RX_US1 0xA0A8
+#define YT8614_REG_COM_PKG_RX_ERR 0xA0A9
+#define YT8614_REG_COM_PKG_RX_OS_BAD 0xA0AA
+#define YT8614_REG_COM_PKG_RX_FRAG 0xA0AB
+#define YT8614_REG_COM_PKG_RX_NOSFD 0xA0AC
+#define YT8614_REG_COM_PKG_TX_VALID0 0xA0AD
+#define YT8614_REG_COM_PKG_TX_VALID1 0xA0AE
+#define YT8614_REG_COM_PKG_TX_OS0 0xA0AF
+
+#define YT8614_REG_COM_PKG_TX_OS1 0xA0B0
+#define YT8614_REG_COM_PKG_TX_US0 0xA0B1
+#define YT8614_REG_COM_PKG_TX_US1 0xA0B2
+#define YT8614_REG_COM_PKG_TX_ERR 0xA0B3
+#define YT8614_REG_COM_PKG_TX_OS_BAD 0xA0B4
+#define YT8614_REG_COM_PKG_TX_FRAG 0xA0B5
+#define YT8614_REG_COM_PKG_TX_NOSFD 0xA0B6
+#define YT8614_REG_COM_PKG_CFG3 0xA0B7
+#define YT8614_REG_COM_PKG_AZ_CFG 0xA0B8
+#define YT8614_REG_COM_PKG_DA_SA_CFG3 0xA0B9
+
+#define YT8614_REG_COM_MANU_HW_RESET 0xA0C0
+
+/* YT8614 UTP MII register: same as generic phy register definitions */
+#define REG_MII_BMCR 0x00 /* Basic mode control register */
+#define REG_MII_BMSR 0x01 /* Basic mode status register */
+#define REG_MII_PHYSID1 0x02 /* PHYS ID 1 */
+#define REG_MII_PHYSID2 0x03 /* PHYS ID 2 */
+#define REG_MII_ADVERTISE 0x04 /* Advertisement control reg */
+#define REG_MII_LPA 0x05 /* Link partner ability reg */
+#define REG_MII_EXPANSION 0x06 /* Expansion register */
+#define REG_MII_NEXT_PAGE 0x07 /* Next page register */
+#define REG_MII_LPR_NEXT_PAGE 0x08 /* LPR next page register */
+#define REG_MII_CTRL1000 0x09 /* 1000BASE-T control */
+#define REG_MII_STAT1000 0x0A /* 1000BASE-T status */
+
+#define REG_MII_MMD_CTRL 0x0D /* MMD access control register */
+#define REG_MII_MMD_DATA 0x0E /* MMD access data register */
+
+#define REG_MII_ESTATUS 0x0F /* Extended Status */
+#define REG_MII_SPEC_CTRL 0x10 /* PHY specific func control */
+#define REG_MII_SPEC_STATUS 0x11 /* PHY specific status */
+#define REG_MII_INT_MASK 0x12 /* Interrupt mask register */
+#define REG_MII_INT_STATUS 0x13 /* Interrupt status register */
+#define REG_MII_DOWNG_CTRL 0x14 /* Speed auto downgrade control*/
+#define REG_MII_RERRCOUNTER 0x15 /* Receive error counter */
+
+#define REG_MII_EXT_ADDR 0x1E /* Extended reg's address */
+#define REG_MII_EXT_DATA 0x1F /* Extended reg's date */
+
+#ifndef MII_BMSR
+#define MII_BMSR REG_MII_BMSR
+#endif
+
+#ifndef YT8614_SPEED_MODE_BIT
+#define YT8614_SPEED_MODE 0xc000
+#define YT8614_DUPLEX 0x2000
+#define YT8614_SPEED_MODE_BIT 14
+#define YT8614_DUPLEX_BIT 13
+#define YT8614_LINK_STATUS_BIT 10
+
+#endif
+
+#define YT8614_REG_COM_HIDE_SPEED_CMB_PRI 0x2000
+
+/* YT8614 UTP MMD register */
+#define YT8614_REG_UTP_MMD_CTRL1 0x00 /* PCS control 1 register */
+#define YT8614_REG_UTP_MMD_STATUS1 0x01 /* PCS status 1 register */
+#define YT8614_REG_UTP_MMD_EEE_CTRL 0x14 /* EEE control and capability */
+#define YT8614_REG_UTP_MMD_EEE_WK_ERR_CNT 0x16 /* EEE wake error counter */
+#define YT8614_REG_UTP_MMD_EEE_LOCAL_ABI 0x3C /* local device EEE ability */
+#define YT8614_REG_UTP_MMD_EEE_LP_ABI 0x3D /* link partner EEE ability */
+#define YT8614_REG_UTP_MMD_EEE_AUTONEG_RES 0x8000 /* autoneg result of EEE */
+
+/* YT8614 UTP EXT register */
+#define YT8614_REG_UTP_EXT_LPBK 0x0A
+#define YT8614_REG_UTP_EXT_SLEEP_CTRL1 0x27
+#define YT8614_REG_UTP_EXT_DEBUG_MON1 0x5A
+#define YT8614_REG_UTP_EXT_DEBUG_MON2 0x5B
+#define YT8614_REG_UTP_EXT_DEBUG_MON3 0x5C
+#define YT8614_REG_UTP_EXT_DEBUG_MON4 0x5D
+
+/* YT8614 SDS(1.25G/5G) MII register: same as YT8521S */
+#define REG_SDS_BMCR 0x00 /* Basic mode control register */
+#define REG_SDS_BMSR 0x01 /* Basic mode status register */
+#define REG_SDS_PHYSID1 0x02 /* PHYS ID 1 */
+#define REG_SDS_PHYSID2 0x03 /* PHYS ID 2 */
+#define REG_SDS_ADVERTISE 0x04 /* Advertisement control reg */
+#define REG_SDS_LPA 0x05 /* Link partner ability reg */
+#define REG_SDS_EXPANSION 0x06 /* Expansion register */
+#define REG_SDS_NEXT_PAGE 0x07 /* Next page register */
+#define REG_SDS_LPR_NEXT_PAGE 0x08 /* LPR next page register */
+
+#define REG_SDS_ESTATUS 0x0F /* Extended Status */
+#define REG_SDS_SPEC_STATUS 0x11 /* SDS specific status */
+
+#define REG_SDS_100FX_CFG 0x14 /* 100fx cfg */
+#define REG_SDS_RERRCOUNTER 0x15 /* Receive error counter */
+#define REG_SDS_LINT_FAIL_CNT 0x16 /* Lint fail counter mon */
+
+/* YT8614 SDS(5G) EXT register */
+#define YT8614_REG_QSGMII_EXT_ANA_DIG_CFG 0x02 /* sds analog digital interface cfg */
+#define YT8614_REG_QSGMII_EXT_PRBS_CFG1 0x05 /* sds prbs cfg1 */
+#define YT8614_REG_QSGMII_EXT_PRBS_CFG2_1 0x06 /* sds prbs cfg2 */
+#define YT8614_REG_QSGMII_EXT_PRBS_CFG2_2 0x07 /* sds prbs cfg2 */
+#define YT8614_REG_QSGMII_EXT_PRBS_MON1 0x08 /* sds prbs mon1 */
+#define YT8614_REG_QSGMII_EXT_PRBS_MON2 0x09 /* sds prbs mon2 */
+#define YT8614_REG_QSGMII_EXT_PRBS_MON3 0x0A /* sds prbs mon3 */
+#define YT8614_REG_QSGMII_EXT_PRBS_MON4 0x0B /* sds prbs mon4 */
+#define YT8614_REG_QSGMII_EXT_PRBS_MON5 0x0C /* sds prbs mon5 */
+#define YT8614_REG_QSGMII_EXT_ANA_CFG2 0xA1 /* Analog cfg2 */
+
+/* YT8614 SDS(1.25G) EXT register */
+#define YT8614_REG_SGMII_EXT_PRBS_CFG1 0x05 /* sds prbs cfg1 */
+#define YT8614_REG_SGMII_EXT_PRBS_CFG2 0x06 /* sds prbs cfg2 */
+#define YT8614_REG_SGMII_EXT_PRBS_MON1 0x08 /* sds prbs mon1 */
+#define YT8614_REG_SGMII_EXT_PRBS_MON2 0x09 /* sds prbs mon2 */
+#define YT8614_REG_SGMII_EXT_PRBS_MON3 0x0A /* sds prbs mon3 */
+#define YT8614_REG_SGMII_EXT_PRBS_MON4 0x0B /* sds prbs mon4 */
+#define YT8614_REG_SGMII_EXT_PRBS_MON5 0x0C /* sds prbs mon5 */
+#define YT8614_REG_SGMII_EXT_ANA_CFG2 0xA1 /* Analog cfg2 */
+#define YT8614_REG_SGMII_EXT_HIDE_AUTO_SEN 0xA5 /* Fiber auto sensing */
+
+////////////////////////////////////////////////////////////////////
+#define YT8614_MMD_DEV_ADDR1 0x1
+#define YT8614_MMD_DEV_ADDR3 0x3
+#define YT8614_MMD_DEV_ADDR7 0x7
+#define YT8614_MMD_DEV_ADDR_NONE 0xFF
+
+/**********YT8521S************************************************/
+/* Basic mode control register(0x00) */
+#define BMCR_RESV 0x003f /* Unused... */
+#define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */
+#define BMCR_CTST 0x0080 /* Collision test */
+#define BMCR_FULLDPLX 0x0100 /* Full duplex */
+#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */
+#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */
+#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */
+#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */
+#define BMCR_SPEED100 0x2000 /* Select 100Mbps */
+#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */
+#define BMCR_RESET 0x8000 /* Reset the DP83840 */
+
+/* Basic mode status register(0x01) */
+#define BMSR_ERCAP 0x0001 /* Ext-reg capability */
+#define BMSR_JCD 0x0002 /* Jabber detected */
+#define BMSR_LSTATUS 0x0004 /* Link status */
+#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
+#define BMSR_RFAULT 0x0010 /* Remote fault detected */
+#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
+#define BMSR_RESV 0x00c0 /* Unused... */
+#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */
+#define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */
+#define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */
+#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
+#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
+#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
+#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */
+#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */
+
+/* Advertisement control register(0x04) */
+#define ADVERTISE_SLCT 0x001f /* Selector bits */
+#define ADVERTISE_CSMA 0x0001 /* Only selector supported */
+#define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */
+#define ADVERTISE_1000XFULL 0x0020 /* Try for 1000BASE-X full-duplex */
+#define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */
+#define ADVERTISE_1000XHALF 0x0040 /* Try for 1000BASE-X half-duplex */
+#define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */
+#define ADVERTISE_1000XPAUSE 0x0080 /* Try for 1000BASE-X pause */
+#define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */
+#define ADVERTISE_1000XPSE_ASYM 0x0100 /* Try for 1000BASE-X asym pause */
+#define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */
+#define ADVERTISE_PAUSE_CAP 0x0400 /* Try for pause */
+#define ADVERTISE_PAUSE_ASYM 0x0800 /* Try for asymetric pause */
+#define ADVERTISE_RESV 0x1000 /* Unused... */
+#define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */
+#define ADVERTISE_LPACK 0x4000 /* Ack link partners response */
+#define ADVERTISE_NPAGE 0x8000 /* Next page bit */
+
+#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | ADVERTISE_CSMA)
+#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
+ ADVERTISE_100HALF | ADVERTISE_100FULL)
+
+/* Link partner ability register(0x05) */
+#define LPA_SLCT 0x001f /* Same as advertise selector */
+#define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */
+#define LPA_1000XFULL 0x0020 /* Can do 1000BASE-X full-duplex */
+#define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */
+#define LPA_1000XHALF 0x0040 /* Can do 1000BASE-X half-duplex */
+#define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */
+#define LPA_1000XPAUSE 0x0080 /* Can do 1000BASE-X pause */
+#define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */
+#define LPA_1000XPAUSE_ASYM 0x0100 /* Can do 1000BASE-X pause asym */
+#define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */
+#define LPA_PAUSE_CAP 0x0400 /* Can pause */
+#define LPA_PAUSE_ASYM 0x0800 /* Can pause asymetrically */
+#define LPA_RESV 0x1000 /* Unused... */
+#define LPA_RFAULT 0x2000 /* Link partner faulted */
+#define LPA_LPACK 0x4000 /* Link partner acked us */
+#define LPA_NPAGE 0x8000 /* Next page bit */
+
+/* 1000BASE-T Control register(0x09) */
+#define ADVERTISE_1000FULL 0x0200 /* Advertise 1000BASE-T full duplex */
+#define ADVERTISE_1000HALF 0x0100 /* Advertise 1000BASE-T half duplex */
+#define CTL1000_AS_MASTER 0x0800
+#define CTL1000_ENABLE_MASTER 0x1000
+
+/* 1000BASE-T Status register(0x0A) */
+#define LPA_1000LOCALRXOK 0x2000 /* Link partner local receiver status */
+#define LPA_1000REMRXOK 0x1000 /* Link partner remote receiver status */
+#define LPA_1000FULL 0x0800 /* Link partner 1000BASE-T full duplex */
+#define LPA_1000HALF 0x0400 /* Link partner 1000BASE-T half duplex */
+
+/**********YT8614************************************************/
+/* Basic mode control register(0x00) */
+#define FIBER_BMCR_RESV 0x001f /* b[4:0] Unused... */
+#define FIBER_BMCR_EN_UNIDIR 0x0020 /* b[5] Valid when bit 0.12 is zero and bit 0.8 is one */
+#define FIBER_BMCR_SPEED1000 0x0040 /* b[6] MSB of Speed (1000) */
+#define FIBER_BMCR_CTST 0x0080 /* b[7] Collision test */
+#define FIBER_BMCR_DUPLEX_MODE 0x0100 /* b[8] Duplex mode */
+#define FIBER_BMCR_ANRESTART 0x0200 /* b[9] Auto negotiation restart */
+#define FIBER_BMCR_ISOLATE 0x0400 /* b[10] Isolate phy from RGMII/SGMII/FIBER */
+#define FIBER_BMCR_PDOWN 0x0800 /* b[11] 1: Power down */
+#define FIBER_BMCR_ANENABLE 0x1000 /* b[12] Enable auto negotiation */
+#define FIBER_BMCR_SPEED100 0x2000 /* b[13] LSB of Speed (100) */
+#define FIBER_BMCR_LOOPBACK 0x4000 /* b[14] Internal loopback control */
+#define FIBER_BMCR_RESET 0x8000 /* b[15] PHY Software Reset(self-clear) */
+
+/* Sds specific status register(0x11) */
+#define FIBER_SSR_ERCAP 0x0001 /* b[0] realtime syncstatus */
+#define FIBER_SSR_XMIT 0x000E /* b[3:1] realtime transmit statemachine.
+ 001: Xmit Idle;
+ 010: Xmit Config;
+ 100: Xmit Data. */
+#define FIBER_SSR_SER_MODE_CFG 0x0030 /* b[5:4] realtime serdes working mode.
+ 00: SG_MAC;
+ 01: SG_PHY;
+ 10: FIB_1000;
+ 11: FIB_100. */
+#define FIBER_SSR_EN_FLOWCTRL_TX 0x0040 /* b[6] realtime en_flowctrl_tx */
+#define FIBER_SSR_EN_FLOWCTRL_RX 0x0080 /* b[7] realtime en_flowctrl_rx */
+#define FIBER_SSR_DUPLEX_ERROR 0x0100 /* b[8] realtime deplex error */
+#define FIBER_SSR_RX_LPI_ACTIVE 0x0200 /* b[9] rx lpi is active */
+#define FIBER_SSR_LSTATUS 0x0400 /* b[10] Link status real-time */
+#define FIBER_SSR_PAUSE 0x1800 /* b[12:11] Pause to mac */
+#define FIBER_SSR_DUPLEX 0x2000 /* b[13] This status bit is valid only when bit10 is 1.
+ 1: full duplex
+ 0: half duplex */
+#define FIBER_SSR_SPEED_MODE 0xC000 /* b[15:14] These status bits are valid only when bit10 is 1.
+ 10---1000M
+ 01---100M */
+
+/* SLED cfg0 (ext 0xA001) */
+#define FIBER_SLED_CFG0_EN_CTRL 0x00FF /* b[7:0] Control to enable the eight ports' SLED */
+#define FIBER_SLED_CFG0_BIT_MASK 0x0700 /* b[10:8] 1: enable the pin output */
+#define FIBER_SLED_CFG0_ACT_LOW 0x0800 /* b[11] control SLED's polarity. 1: active low; 0: active high */
+#define FIBER_SLED_CFG0_MANU_ST 0x7000 /* b[14:12] SLEDs' manul status, corresponding to each port's 3 SLEDs */
+#define FIBER_SLED_CFG0_MANU_EN 0x8000 /* b[15] to control serial LEDs status manually */
+
+/**********YT8614************************************************/
+/* Fiber auto sensing(sgmii ext 0xA5) */
+#define FIBER_AUTO_SEN_ENABLE 0x8000 /* b[15] Enable fiber auto sensing */
+
+/* Fiber force speed(common ext 0xA009) */
+#define FIBER_FORCE_1000M 0x0001 /* b[0] 1:1000BX 0:100FX */
+
+#ifndef NULL
+#define NULL 0
+#endif
+
+/* errno */
+enum ytphy_8614_errno_e
+{
+ SYS_E_NONE,
+ SYS_E_PARAM,
+ SYS_E_MAX
+};
+
+/* errno */
+enum ytphy_8614_combo_speed_e
+{
+ YT8614_COMBO_FIBER_1000M,
+ YT8614_COMBO_FIBER_100M,
+ YT8614_COMBO_UTP_ONLY,
+ YT8614_COMBO_SPEED_MAX
+};
+
+/* definition for porting */
+/* phy registers access */
+typedef struct
+{
+ u16 reg; /* the offset of the phy internal address */
+ u16 val; /* the value of the register */
+ u8 regType; /* register type */
+} phy_data_s;
+
+/* for porting use.
+ * pls over-write member function read/write for mdio access
+ */
+typedef struct phy_info_str
+{
+#if 0
+ struct phy_device *phydev;
+ int mdio_base;
+#endif
+ unsigned int lport;
+ unsigned int bus_id;
+ unsigned int phy_addr;
+
+ s32 (*read)(struct phy_info_str *info, phy_data_s *param);
+ s32 (*write)(struct phy_info_str *info, phy_data_s *param);
+}phy_info_s;
+
+/* get phy access method */
+s32 yt8614_read_reg(struct phy_info_str *info, phy_data_s *param);
+s32 yt8614_write_reg(struct phy_info_str *info, phy_data_s *param);
+s32 yt8614_phy_soft_reset(u32 lport);
+s32 yt8614_phy_init(u32 lport);
+s32 yt8614_fiber_enable(u32 lport, BOOL enable);
+s32 yt8614_utp_enable(u32 lport, BOOL enable);
+s32 yt8614_fiber_unidirection_set(u32 lport, int speed, BOOL enable);
+s32 yt8614_fiber_autosensing_set(u32 lport, BOOL enable);
+s32 yt8614_fiber_speed_set(u32 lport, int fiber_speed);
+s32 yt8614_qsgmii_autoneg_set(u32 lport, BOOL enable);
+s32 yt8614_sgmii_autoneg_set(u32 lport, BOOL enable);
+s32 yt8614_qsgmii_sgmii_link_status_get(u32 lport, BOOL *enable, BOOL if_qsgmii);
+int yt8614_combo_media_priority_set (u32 lport, int fiber);
+int yt8614_combo_media_priority_get (u32 lport, int *fiber);
+s32 yt8614_utp_autoneg_set(u32 lport, BOOL enable);
+s32 yt8614_utp_autoneg_get(u32 lport, BOOL *enable);
+s32 yt8614_utp_autoneg_ability_set(u32 lport, unsigned int cap_mask);
+s32 yt8614_utp_autoneg_ability_get(u32 lport, unsigned int *cap_mask);
+s32 yt8614_utp_force_duplex_set(u32 lport, BOOL full);
+s32 yt8614_utp_force_duplex_get(u32 lport, BOOL *full);
+s32 yt8614_utp_force_speed_set(u32 lport, unsigned int speed);
+s32 yt8614_utp_force_speed_get(u32 lport, unsigned int *speed);
+int yt8614_autoneg_done_get (u32 lport, int speed, int *aneg);
+int yt8614_media_status_get(u32 lport, int* speed, int* duplex, int* ret_link, int *media);
+
+#endif
diff --git a/include/linux/motorcomm_phy.h b/include/linux/motorcomm_phy.h
new file mode 100644
index 000000000..9e01fc205
--- /dev/null
+++ b/include/linux/motorcomm_phy.h
@@ -0,0 +1,119 @@
+/*
+ * include/linux/motorcomm_phy.h
+ *
+ * Motorcomm PHY IDs
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef _MOTORCOMM_PHY_H
+#define _MOTORCOMM_PHY_H
+
+#define MOTORCOMM_PHY_ID_MASK 0x00000fff
+#define MOTORCOMM_PHY_ID_8531_MASK 0xffffffff
+#define MOTORCOMM_MPHY_ID_MASK 0x0000ffff
+
+#define PHY_ID_YT8010 0x00000309
+#define PHY_ID_YT8510 0x00000109
+#define PHY_ID_YT8511 0x0000010a
+#define PHY_ID_YT8512 0x00000118
+#define PHY_ID_YT8512B 0x00000128
+#define PHY_ID_YT8521 0x0000011a
+#define PHY_ID_YT8531S 0x4f51e91a
+#define PHY_ID_YT8531 0x4f51e91b
+//#define PHY_ID_YT8614 0x0000e899
+#define PHY_ID_YT8618 0x0000e889
+
+#define REG_PHY_SPEC_STATUS 0x11
+#define REG_DEBUG_ADDR_OFFSET 0x1e
+#define REG_DEBUG_DATA 0x1f
+
+#define YT8512_EXTREG_AFE_PLL 0x50
+#define YT8512_EXTREG_EXTEND_COMBO 0x4000
+#define YT8512_EXTREG_LED0 0x40c0
+#define YT8512_EXTREG_LED1 0x40c3
+
+#define YT8512_EXTREG_SLEEP_CONTROL1 0x2027
+
+#define YT_SOFTWARE_RESET 0x8000
+
+#define YT8512_CONFIG_PLL_REFCLK_SEL_EN 0x0040
+#define YT8512_CONTROL1_RMII_EN 0x0001
+#define YT8512_LED0_ACT_BLK_IND 0x1000
+#define YT8512_LED0_DIS_LED_AN_TRY 0x0001
+#define YT8512_LED0_BT_BLK_EN 0x0002
+#define YT8512_LED0_HT_BLK_EN 0x0004
+#define YT8512_LED0_COL_BLK_EN 0x0008
+#define YT8512_LED0_BT_ON_EN 0x0010
+#define YT8512_LED1_BT_ON_EN 0x0010
+#define YT8512_LED1_TXACT_BLK_EN 0x0100
+#define YT8512_LED1_RXACT_BLK_EN 0x0200
+#define YT8512_SPEED_MODE 0xc000
+#define YT8512_DUPLEX 0x2000
+
+#define YT8512_SPEED_MODE_BIT 14
+#define YT8512_DUPLEX_BIT 13
+#define YT8512_EN_SLEEP_SW_BIT 15
+
+#define YT8521_EXTREG_SLEEP_CONTROL1 0x27
+#define YT8521_EN_SLEEP_SW_BIT 15
+
+#define YT8521_SPEED_MODE 0xc000
+#define YT8521_DUPLEX 0x2000
+#define YT8521_SPEED_MODE_BIT 14
+#define YT8521_DUPLEX_BIT 13
+#define YT8521_LINK_STATUS_BIT 10
+
+/* based on yt8521 wol config register */
+#define YTPHY_UTP_INTR_REG 0x12
+/* WOL Event Interrupt Enable */
+#define YTPHY_WOL_INTR BIT(6)
+
+/* Magic Packet MAC address registers */
+#define YTPHY_MAGIC_PACKET_MAC_ADDR2 0xa007
+#define YTPHY_MAGIC_PACKET_MAC_ADDR1 0xa008
+#define YTPHY_MAGIC_PACKET_MAC_ADDR0 0xa009
+
+#define YTPHY_WOL_CFG_REG 0xa00a
+#define YTPHY_WOL_CFG_TYPE BIT(0) /* WOL TYPE */
+#define YTPHY_WOL_CFG_EN BIT(3) /* WOL Enable */
+#define YTPHY_WOL_CFG_INTR_SEL BIT(6) /* WOL Event Interrupt Enable */
+#define YTPHY_WOL_CFG_WIDTH1 BIT(1) /* WOL Pulse Width */
+#define YTPHY_WOL_CFG_WIDTH2 BIT(2)
+
+#define YTPHY_REG_SPACE_UTP 0
+#define YTPHY_REG_SPACE_FIBER 2
+
+enum ytphy_wol_type_e
+{
+ YTPHY_WOL_TYPE_LEVEL,
+ YTPHY_WOL_TYPE_PULSE,
+ YTPHY_WOL_TYPE_MAX
+};
+typedef enum ytphy_wol_type_e ytphy_wol_type_t;
+
+enum ytphy_wol_width_e
+{
+ YTPHY_WOL_WIDTH_84MS,
+ YTPHY_WOL_WIDTH_168MS,
+ YTPHY_WOL_WIDTH_336MS,
+ YTPHY_WOL_WIDTH_672MS,
+ YTPHY_WOL_WIDTH_MAX
+};
+typedef enum ytphy_wol_width_e ytphy_wol_width_t;
+
+struct ytphy_wol_cfg_s
+{
+ int enable;
+ int type;
+ int width;
+};
+typedef struct ytphy_wol_cfg_s ytphy_wol_cfg_t;
+
+#endif /* _MOTORCOMM_PHY_H */
+
+
--
2.35.3
Reference in New Issue View Git Blame Copy Permalink