106 lines
3.1 KiB
Diff
106 lines
3.1 KiB
Diff
From 373e8abe03637021c7564f0d474dc5e2364e1504 Mon Sep 17 00:00:00 2001
|
|
From: =?UTF-8?q?Ond=C5=99ej=20Jirman?= <megi@xff.cz>
|
|
Date: Tue, 20 Aug 2019 14:54:48 +0200
|
|
Subject: [PATCH 061/391] arm64: dts: allwinner: orange-pi-3: Enable ethernet
|
|
|
|
Orange Pi 3 has two regulators that power the Realtek RTL8211E
|
|
PHY. According to the datasheet, both regulators need to be enabled
|
|
at the same time, or that "phy-io" should be enabled slightly earlier
|
|
than "phy" regulator.
|
|
|
|
RTL8211E/RTL8211EG datasheet says:
|
|
|
|
Note 4: 2.5V (or 1.8/1.5V) RGMII power should be risen simultaneously
|
|
or slightly earlier than 3.3V power. Rising 2.5V (or 1.8/1.5V) power
|
|
later than 3.3V power may lead to errors.
|
|
|
|
The driver ensures the regulator enable ordering. The timing is set
|
|
in DT via startup-delay-us.
|
|
|
|
We also need to wait at least 30ms after power-up/reset, before
|
|
accessing the PHY registers.
|
|
|
|
All values of RX/TX delay were tested exhaustively and a middle one
|
|
of the range of working values was chosen.
|
|
|
|
Signed-off-by: Ondrej Jirman <megi@xff.cz>
|
|
---
|
|
.../dts/allwinner/sun50i-h6-orangepi-3.dts | 40 +++++++++++++++++++
|
|
1 file changed, 40 insertions(+)
|
|
|
|
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
|
|
index 6fc65e8db..c2ea73d43 100644
|
|
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
|
|
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
|
|
@@ -15,6 +15,7 @@ / {
|
|
aliases {
|
|
serial0 = &uart0;
|
|
serial1 = &uart1;
|
|
+ ethernet0 = &emac;
|
|
};
|
|
|
|
chosen {
|
|
@@ -64,6 +65,15 @@ reg_vcc5v: vcc5v {
|
|
regulator-always-on;
|
|
};
|
|
|
|
+ reg_gmac_2v5: gmac-2v5 {
|
|
+ compatible = "regulator-fixed";
|
|
+ regulator-name = "gmac-2v5";
|
|
+ regulator-min-microvolt = <2500000>;
|
|
+ regulator-max-microvolt = <2500000>;
|
|
+ enable-active-high;
|
|
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
|
|
+ };
|
|
+
|
|
reg_vcc33_wifi: vcc33-wifi {
|
|
/* Always on 3.3V regulator for WiFi and BT */
|
|
compatible = "regulator-fixed";
|
|
@@ -128,6 +138,35 @@ hdmi_out_con: endpoint {
|
|
};
|
|
};
|
|
|
|
+&emac {
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&ext_rgmii_pins>;
|
|
+ phy-mode = "rgmii-id";
|
|
+ phy-handle = <&ext_rgmii_phy>;
|
|
+ /*
|
|
+ * The board uses 2.5V RGMII signalling. Power sequence to enable
|
|
+ * the phy is to enable GMAC-2V5 and GMAC-3V (aldo2) power rails
|
|
+ * at the same time and to wait 100ms. The driver enables phy-io
|
|
+ * first. Delay is achieved with enable-ramp-delay on reg_aldo2.
|
|
+ */
|
|
+ phy-supply = <®_aldo2>;
|
|
+ phy-io-supply = <®_gmac_2v5>;
|
|
+ allwinner,rx-delay-ps = <200>;
|
|
+ allwinner,tx-delay-ps = <200>;
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+&mdio {
|
|
+ ext_rgmii_phy: ethernet-phy@1 {
|
|
+ compatible = "ethernet-phy-ieee802.3-c22";
|
|
+ reg = <1>;
|
|
+
|
|
+ reset-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
|
|
+ reset-assert-us = <15000>;
|
|
+ reset-deassert-us = <40000>;
|
|
+ };
|
|
+};
|
|
+
|
|
&mmc0 {
|
|
vmmc-supply = <®_cldo1>;
|
|
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
|
|
@@ -211,6 +250,7 @@ reg_aldo2: aldo2 {
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-name = "vcc33-audio-tv-ephy-mac";
|
|
+ regulator-enable-ramp-delay = <100000>;
|
|
};
|
|
|
|
/* ALDO3 is shorted to CLDO1 */
|
|
--
|
|
2.35.3
|
|
|