188 lines
4.0 KiB
Bash
188 lines
4.0 KiB
Bash
#!/bin/bash
|
|
#
|
|
# pintest
|
|
# Test the Pi's GPIO port
|
|
# Copyright (c) 2013-2015 Gordon Henderson
|
|
#################################################################################
|
|
# This file is part of wiringPi:
|
|
# A "wiring" library for the Raspberry Pi
|
|
#
|
|
# wiringPi is free software: you can redistribute it and/or modify
|
|
# it under the terms of the GNU Lesser General Public License as published by
|
|
# the Free Software Foundation, either version 3 of the License, or
|
|
# (at your option) any later version.
|
|
#
|
|
# wiringPi is distributed in the hope that it will be useful,
|
|
# but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
# GNU Lesser General Public License for more details.
|
|
#
|
|
# You should have received a copy of the GNU Lesser General Public License
|
|
# along with wiringPi. If not, see <http://www.gnu.org/licenses/>.
|
|
#################################################################################
|
|
|
|
|
|
# logErr pin, expected got
|
|
################################################################################
|
|
|
|
logErr ()
|
|
{
|
|
if [ $errs = 0 ]; then
|
|
echo ""
|
|
fi
|
|
echo " --> Pin $1 failure. Expected $2, got $3"
|
|
let errs+=1
|
|
}
|
|
|
|
|
|
# printErrorCount
|
|
################################################################################
|
|
|
|
printErrCount()
|
|
{
|
|
if [ $errs = 0 ]; then
|
|
echo "No faults detected."
|
|
elif [ $errs = 1 ]; then
|
|
echo "One fault detected."
|
|
else
|
|
echo "$errs faults detected"
|
|
fi
|
|
}
|
|
|
|
|
|
# testPins start end
|
|
################################################################################
|
|
|
|
testPins()
|
|
{
|
|
start=$1
|
|
end=$2
|
|
errs=0
|
|
|
|
printf "%30s %2d:%2d: " "$3" $1 $2
|
|
|
|
# Set range to inputs
|
|
|
|
for i in `seq $start $end`; do
|
|
gpio mode $i in
|
|
done
|
|
|
|
# Enable internal pull-ups and expect to read high
|
|
|
|
for i in `seq $start $end`; do
|
|
gpio mode $i up
|
|
if [ `gpio read $i` = 0 ]; then
|
|
logErr $i 1 0
|
|
fi
|
|
done
|
|
|
|
# Enable internal pull-downs and expect to read low
|
|
|
|
for i in `seq $start $end`; do
|
|
gpio mode $i down
|
|
if [ `gpio read $i` = 1 ]; then
|
|
echo "Pin $i failure - expected 0, got 1"
|
|
let errs+=1
|
|
fi
|
|
done
|
|
|
|
# Remove the internal pull up/downs
|
|
|
|
for i in `seq $start $end`; do
|
|
gpio mode $i tri
|
|
done
|
|
|
|
if [ $errs = 0 ]; then
|
|
echo " OK"
|
|
else
|
|
printErrCount
|
|
fi
|
|
|
|
let totErrs+=errs
|
|
}
|
|
|
|
|
|
intro()
|
|
{
|
|
cat <<EOF
|
|
PinTest
|
|
=======
|
|
|
|
This is a simple utility to test the GPIO pins on your Raspberry Pi.
|
|
|
|
NOTE: All GPIO peripherals must be removed to perform this test. This
|
|
includes serial, I2C and SPI connections. You may get incorrect results
|
|
if something is connected and it interferes with the test.
|
|
|
|
This test can only test the input side of things. It uses the internal
|
|
pull-up and pull-down resistors to simulate inputs. It does not test
|
|
the output drivers.
|
|
|
|
You will need to reboot your Pi after this test if you wish to use the
|
|
serial port as it will be left in GPIO mode rather than serial mode.
|
|
|
|
This test only tests the original pins present on the Rev A and B. It
|
|
does not test the extra pins on the Revision A2, B2 nor the A+ or B+
|
|
|
|
Please make sure everything is removed and press the ENTER key to continue,
|
|
EOF
|
|
|
|
echo -n "or Control-C to abort... "
|
|
read a
|
|
}
|
|
|
|
|
|
# Start here
|
|
################################################################################
|
|
|
|
intro
|
|
gpio unexportall
|
|
|
|
errs=0
|
|
totErrs=0
|
|
|
|
echo ""
|
|
|
|
# Main pins
|
|
|
|
testPins 0 7 "The main 8 GPIO pins"
|
|
|
|
# SPI
|
|
|
|
testPins 10 14 "The 5 SPI pins"
|
|
|
|
# Serial
|
|
|
|
testPins 15 16 "The serial pins"
|
|
|
|
# I2C - Needs somewhat different testing
|
|
# due to the on-board pull-up's
|
|
|
|
echo -n " The I2C pins 8: 9: "
|
|
errs=0
|
|
gpio mode 8 in
|
|
gpio mode 9 in
|
|
|
|
if [ `gpio read 8` = 0 ]; then
|
|
echo "Pin 8 failure - expected 1, got 0"
|
|
let errs+=1
|
|
fi
|
|
|
|
if [ `gpio read 9` = 0 ]; then
|
|
echo "Pin 9 failure - expected 1, got 0"
|
|
let errs+=1
|
|
fi
|
|
|
|
if [ $errs = 0 ]; then
|
|
echo " OK"
|
|
else
|
|
printErrCount
|
|
fi
|
|
|
|
echo ""
|
|
if [ $totErrs != 0 ]; then
|
|
echo ""
|
|
echo "Faults detected! Output of 'readall':"
|
|
gpio readall
|
|
fi
|